Search results

Pm sent

Your gonna need efuel. I talked with jim at rosewood about it when I got my 160/80s from him. Efuel is a neccesity to keep these Injectors happy as a mechanical pump can barely keep up with stock aa injectors found in the obs trucks.

Unplugging the icp sensor it should still run ok. The pcm just uses base numbers then for icp. If you didnt have lube oil pressure (lpop) it wouldnt run since the lpop feeds ur high pressure oil pump. I would stil put in a mechanical gauge, u can use one of the ports on the hpop reservoir. That...

Here is a different picture for you where it is referred as an anti-drainback valve

International calls it a short circuit valve. In all actuality it is an oil pressure bypass valve. Its in the top of the block. Look at the diagram I posted. Its the part in the square and goes into the front top section of the block. Its part of the oiling system. I assure you I am not smoking...

here is a pic of where the valve is located. drivers side of the block by the hpop reservoir. I have a t444e international engine from a school bus in my truck so I have the cast iron reservoir. Mine looks like i may be able to get it out without removing the reservoir but figured i would check...

this may be completely off subject. but has anyone ever taken their "short circuit valve" out of the block to inspect and clean it? I was reading about someone on psn that had a very strange problem and ended up having a piece of silicone stuck in this short circuit valve causing all kinds of...

Looking for a 7.3 van turbo from 99.5 to 03. Economically priced as im unsure how long I will be using it. thanks! Located in memphis, mi if anyone local has one.

Still have the turbo?

I used it on my build and on my dads 02 when his pan rusted thru. Both with new spectra pans from oreilly. No leaks from either one. Both motors were out and hanging from the cherry picker. Cleaned the block real good, and used silicone per the directions.

I went with rosewood. Took a set of ab's. Made them 160cc with 80% nozzles (his stage 2s) great customer service and support. Answered emails quickly even on saturday and quick turn around. Got them back around a week after I shipped them. As he says on his website though, the ab's usually need...

I was running rotell t6 5-40. This started midway thru that oil change. Been chasing the problem for awhile. Now im running 15-40 castrol tection. Only reason I tried that is it was on sale for $11.99 a gallon and I needed an oil change anyway. No change in the way the truck runs. Mine runs fine...

Im having similiar issues. Glad to see im not the only one. Hopefully we can find a solution.

Check at your local oreilly. I was able to get a drivers side manifold for my truck for $100 brand new dorman.

The pedal wasnt gettng 12v power signal.

Truck is on the road and running great. I have about 1000 miles on it. The tach is off by around 400 rpms but I can live with that.

Havent updated on here in a while. Engine harness is done. Trans and tcase are in. I dropped the fuel tank and added a 3/8 pickup and ran 3/8 line from tank to motor with a frame mounted wAter separator. I repinned the dash harness and it seems like it will work fine. Power Windows work, radio...

Looking for a wiring harness for my swap. 99-02 super duty 7.3 auto trans and electronic 4x4. Looking for the harness from firewall plugs to engine junction block. Call/text Josh 810-824-1067 Thanks

We will see how the gasket holds up. It came with studs to mount the pan. The fit was good. A friend of mine that works at international says they've used quite a few and they're great. It better be for the $85 it cost me!! On a good note tho the motor is in the truck. I'm going to start the...

Do you still have the intake spyder?