Search results

  1. E

    4r100 torque converter

    Precision of new Hampton torque converter... Same thing cnc fab sells. And Sam wyse uses on some rebuilds. Low stall... New in box never removed. Was going in my 7.3 but never got around to it. $300 picked up near fort meade maryland or buyer pays shipping.
  2. E

    7.3 ipr and icp readings

    Looked around the forum but I figured I'd ask. I know my readings are crap, would like some input from some of you diesel heads. Around 65-70 percent throttle I'm seeing 1800-1900 psi with 44ish ipr.. number already sucks. This reading is at around 2500rpm, once I hit 2600-2700 rpm the icp...
  3. E

    ibeam pivot bushing dimensions??

    Any one able to post some dimensions for 2000+ ibeam pivot bushing. Need the outside diameter of the bushing shell which would also be the inside diameter of the ibeam bushing location. I dont remember if I retained stock dimensions with the aftermarket beams. Also energy and moog both claim...
  4. E

    Bearing spun on spindle

    My excursion front wheel bearing spun on the spindle a tad... New bearing slides on to the spindle with very little resistance.. I dont have time to do ball joints and spindle at the moment... What do you all think of the idea of knurling the spindle a bit with a punch or chisel then adding...
  5. E

    4-ad 1-ae injectors

    4 ad and a long lead injector.. Removed these from my truck after installing new injectors the other 3 were old and used as cores... Just tested these on a good running truck seemed too be working just fine.. Was told they were rebuilt at ff... Never saw papers never confirmed... Maybe you can...
  6. E

    7.3 banks 6 gun

    Anyone here have a 6 gun icp mod in a 7.3?? I was digging through my junk and found an old 6 gun... Problem is the 2 plug harness that goes to the icp was cut out so now I only have 2 wires and no plugs... Was wondering how they need to be routed... Unlikely anyone still has a 6 gun but if you...
  7. E

    Bent push rods

    Are push rods 100% true? Pulled some out and rolled them on a flat surface only so see that they had a slight warp to them... The gap between the table and rod center changes a bit when I spin them its minimal maybe a couple sheets of paper from high to low spots.. But I found this on almost all...
  8. E

    Autometer elite gauges. Good for classic cars.

    These are a few gauges I wont be using... New in box. Top of the line autometer elite. Were for a mopar project I had. 1- TACHOMETER # 6847- 05705. 10k rpm with bunch of features. 1- FUEL PRESSURE # 5667. Low psi gauge 0-15psi 1- FUEL LEVEL # 5609. 1- Voltmeter #5683. Buy all for...
  9. E

    Diamond T tc reviews???

    Who is running a diamond t torque converter? Any reviews? My tc is getting loose and I'm looking to buy a new one.. Transmission has some miles so I'm looking for a good budget tc... Haven't found much about diamond t.
  10. E

    Eaton fuller transmission questions

    I am thinking of swapping a 13 speed into the excursion... I know I need air going to it which I already have because of the bagged 4 link rear I just finished. My question is, how the air used in these medium/heavy duty transmissions? Do they just hold air pressure or do they bleed any of it...
  11. E

    Another Chugging 7.3

    One of my 7.3s has been chugging for a while now.. Power was a bit low until I disconnected the ebp sensor (in front of the engine) a couple days ago.. After disconnecting it throttle felt responsive and smooth and the chugging at low rpms including idle was reduced a good bit.. Truck also runs...
  12. E

    7.3 excursion 4 link rear lowered.

    I will add as I have time... I also have some youtube videos I will link... I will make more videos if I get requests just let me know what you want to see... Also video kinda sucks still getting the hang of it haha. This is my 03 excursion... Finally decided to give it a proper setup. 4 link...
  13. E

    Icp and ipr readings

    Icp reads 1800-2000 max. Ipr reads 30% max... Both seem low... Fuel pressure is good. New Icp sensor... Old ipr... Maybe needing a new ipr and hpop?? Injector orings are new. Power feels a bit low after I had a low. 10k mod lowers Icp but ipr stays around 30ish... Icp at idle 430-480...

Random media

IMG_0360
Rear grab handle
My Toys
eleanor_part_two_1_
image106
parts
95_powerstoke
The wife taking the truck out for the first time..
IMG_5555
Me trying to balance a power stroke
IMAG0536
My Toys

Latest posts

Members online

Total: 377 (members: 1, guests: 376)
Top