Search results

  1. G

    WTB: 6.0 FICM Logic board

    Looking for a good logic board half of a 4 pin FICM for a '07 6.0. Thanks.
  2. G

    6.0 Starting Issue

    Thanks for your input!
  3. G

    6.0 Starting Issue

    Thanks for your help. I was not able to get a gauge yet but verified no cam fault and the FICM did show it sync'd. The injector test listed #3 & #6 injectors as low circuit. I unplugged the FICM plugs and seated them again and the truck started. The problem now is the keepers on the FICM plugs...
  4. G

    6.0 Starting Issue

    New to 6.0 powerstrokes and having trouble getting my '07 to start after replacing heads & head gaskets. Using AE, the FICM voltage is 48 and the injector pressure slowly builds to 1650-1800psi. The batteries are in good condition holding full charge. Have attempted to start ten or twelve times...
  5. G

    WTB: Bellowed up-pipes for H2E kit

    Looking for a set of bellowed up-pipes for my '02 7.3 with Hypermax H2E turbo kit. Thanks.
  6. G

    WTB: Injector rebuild tools(7.3)

    Looking for tools to rebuild 7.3 powerstroke injectors. Anybody have a used tool set they want to sell? Thanks.
  7. G

    6.0 o-ring head question

    Got in contact with a reputable head mfg. and their tolerance for "o-ring" end gap is a maximum of .050".
  8. G

    6.0 o-ring head question

    Thanks for the replys. The gap is approximately 1/32" which is why it got my attention.
  9. G

    6.0 o-ring head question

    Had a set of 6.0 heads o-ringed and noticed one of they cylinder's ring had a small gap between the wire ends. The other cylinders' didn't appear to have this gap. The machinist said the small gap wouldn't be an issue but I wanted to see if anyone had any experience with this issue. Thanks.
  10. G

    6.0 IPR wiring heat shield

    Is the heat shield on the IPR wiring needed and if so, does anyone have the OEM part number for it? Considered aftermarket thermal jacketing but it won't fit like the OEM part. Thanks.
  11. G

    Wanted: Radiator fittings for 99-03 Superduty

    Thanks for the part number. This is the fitting needed.
  12. G

    Mishimoto radiator transmission fittings

    Mishimoto was contacted about the issue. It took them three days to get back to me only to say they don't have an adapter for my truck's fittings and I would need to come up with my own adapters. After searching for hours and visiting local hydraulic and fitting stores, I am working to fabricate...
  13. G

    Wanted: Radiator fittings for 99-03 Superduty

    The fitting need most is the 5/8-18 SAE inverted flare female (deep fitting) and I can adapt the male fitting. These were the stock fittings found in radiators for most 99-03 surperduty trucks.
  14. G

    Wanted: Radiator fittings for 99-03 Superduty

    Looking for a pair of the fittings that thread in to the radiator for the transmission cooler lines. These are 5/8-18 SAE male to 5/8-18 SAE female. Need these to fabricate a fitting for a Mishimoto radiator installation. Thanks.
  15. G

    Mishimoto radiator transmission fittings

    Installed an aluminum Mishimoto radiator in my 2002 F250 and the radiator's threaded holes for the transmission lines don't match my truck's fittings. The adapters that came with it also don't mate to my truck's transmission lines. Removed the fittings from the original radiator and they don't...
  16. G

    WTB: Stealth billet HPOP

    Looking to purchase a Stealth BILLET HPOP stage II or III. Needs to be complete. Wanting to purchase one to disassemble for measurements. Thanks.
  17. G

    WTB: (1) 20x12 Weld Dune wheel

    Thanks for the help. I check the sites and contact Mr. Merrell.
  18. G

    WTB: (1) 20x12 Weld Dune wheel

    Looking for a single Weld Racing 20x12 Dune wheel.
  19. G

    Used OEM 05-07 Headlights - $80

    Payment made.
  20. G

    WTB: Curt 15316 Class V receiver hitch

    Looking to purchase a good used Curt Class V receiver hitch for a 99-07 F250. PM me if you have a good used one or a new one you decided not to use. Thanks.
Top