Search results

  1. C

    Slow start but fine after

    Mine didn't have a loss of power and even had fairly normal icp pressure. Why didn't it show up on my hp leak check?
  2. C

    Slow start but fine after

    Hpop. Ball bearing fell put along with some seal. I guess my old girl is quite tough, he said he's never seen one run with the ball bearing missing.
  3. C

    Slow start but fine after

    My front cover had a crack by the regulator spring. So had to wait on parts for that. But same results. Will post up when i get it back.
  4. C

    Slow start but fine after

    It's in the shop, now to see what they say.
  5. C

    Slow start but fine after

    Mine is a little 04 so it doesn't have the stc. I used the tool that replaces the ipr valve for leak checks. What really sucks is my back is giving me trouble again so can only stand to work on it about an hr at a time. Figure ill take it over Monday unless i have a stroke of genius between...
  6. C

    Slow start but fine after

    Well i used a shop vac to see if oil could be sucked into the oil filter housing and it did. And then It would pump oil into it when cranking. It did start up again, but took about 20 seconds to build pressure. Then once running it ran at 30 percent ipr. Think ill break down and take it to a...
  7. C

    Slow start but fine after

    Can i do that without pulling the lpop gears out again?
  8. C

    Slow start but fine after

    This is my results. https://youtu.be/kDs2SXVrCK8 I filled the filter housing with oil and held down the drain valve. It held fine. I poured one gallon of oil in the pan and used a shop vac to pull from inlet side of the lpop with the cover off and it had no problem sucking oil up. So maybe a...
  9. C

    Slow start but fine after

    Housing looks good. If I pour oil into the filter housing will it drain back into the pump housing? I was thinking if I leave the cover off the pump and pour a small amount into the filter housing i can see if there is a blockage between the two. Then also fill the oil pan with a gallon or so...
  10. C

    Slow start but fine after

    I stopped by the mechanics shop when he did the oil cooler and it was all cleaned out and he showed me where my old screen still looked good. The ICP currently shows less then 50 psi. When it was still starting up it would jump to whatever was desired. My logger doesn't show in psi and I...
  11. C

    Slow start but fine after

    Well I pulled the pump cover and drained the oil pan to see if I could see anything. The scope wouldn't fit through the passage in the front cover and when looking in the oil pan I could not see anything out of the ordinary. What could be clogged or disconnected that would cause no oil to come...
  12. C

    Slow start but fine after

    The pump looked good, no abnormal wear on the covers and no patterns on the gears. Worst case it may have been a slightly looser tolerance then the new one. But any HP leak would have show up using this correct? http://www.accuratediesel.com/shop/251.html I could tell there was some air...
  13. C

    Slow start but fine after

    I stand corrected on the oil filter test. The truck won't build ICP but also won't fill the oil filter at all now. I first thought the lp oil switch was bad so replaced it, then went to the regulator thinking maybe the spring was weak, then to the pump itself. I am going to drain the pan after...
  14. C

    Slow start but fine after

    Ok, I know this subject seems to have been covered pretty well. But this truck is kicking my azz. It takes a good 20 seconds for it to build high pressure oil both hot or cold and then runs fine. My IPR shows 85% when cranking and once the icp comes up the truck fires up and the IPR drops to...
  15. C

    up fitters in a 99

    I would also like to know how to wire up the factory brake controller. The write up listed is very informative. I can't find any diagrams for the brake controller either.
  16. C

    Sub and amp for the boat

    Hertz is great gear. Open enviroments are hard and space that is direct radiating to the cabin is even harder. I have a digital designs 3500 12. I didn't order it with that coil configuration, it was on the shelf and they made me a deal on it. Sent from my SCH-I535 using Tapatalk
  17. C

    Wanted: HomeLink

    Ok, its in my way so if you can't find a visor just pay shipping and its yours. Sent from my SCH-I535 using Tapatalk
  18. C

    Sub and amp for the boat

    1ohm 2ohm 8ohm etc does not effect sound quality. Its is just the impedance (resistance) of the voice coil. Matching it to a amplifier correctly is what's important. For a boat I would get as high of quality class d or class g/h amplifier that matches the impedance of your driver(sub)...
  19. C

    Wanted: HomeLink

    Would you be interested in just the module? It came out of a 97-02 Lincoln navigator. Ill have to look when I get home as to what color it is. Sent from my SCH-I535 using Tapatalk
  20. C

    Integrated brake controller

    I got it with the lower dash portion for my upfitter upgrade and wont work in my 04. 100 plus shipping.

Random media

IMG_0361
558206_4175518193868_289576718_n
bryanstruck
The Truck
Duramax hauling cattle
tank
08 excursion
photo_42
IPR_plug_2_
424756_3288691704949_1497394897_33116533_797711494_n
Rear
before_and_after1

Latest posts

Members online

No members online now.
Total: 522 (members: 0, guests: 522)
Top