Search results

Looking for any leads on some drivetrain parts. My 10.5 grenaded and I'm looking at swapping in a Dana 80, found a deal local for one with 4:10s but my truck is 3:73 so I'm interested in either a complete dana 80 with 3:73 gears or a 4:10 gear set for my stock dana 60 in my 08 f250 Any help is...

For a 6.0. Looking to sell for a friend that traded his truck in. Is not vin locked or has any issues. $500 Best to call/text me Rodney (570)778-5189

Just what the title says, looking to see if anybody has a set laying around. Thanks Rodney

Just what the title says, looking to see if anybody has a set laying around. Thanks Rodney

Haven't got a chance to check out the forums much lately. Just finished up my daily commuter. 99 ranger with a Mercedes diesel under the hood, jeep 5 speed tranny, runs pretty good, 29mpg with 410 rears that are going ASAP for some 305 or similar

Haven't been on here for a while; thought maybe somebody would be interested Looking to sell my bike to free up some cash. 2009 Kawasaki kx250f, full race bike, built by Evo motorsports, suspension, carb, motor, everything done. Full yosh pipe, front tire 85%, rear tire 50%. 78 hours currently...

I am on 81 headed south on vacation to GNCC race. Something let loose in Trans or transfer case. Anybody nearby near mile marker 107.9 please giver a call. I got all the tools I need to pull Trans ect would like a shop. Have friend coming for trailer but he is 3 hrs away Rodney (570) 7785189 I...

Long story short got a truck in the shop that had the hpop update done to replace the stc fitting. New connector was installed and improperly torqued. Cracked junction block behind hpop, Need discharge tube that diverts oil from hpop to each stand pipe. Anybody that may have one laying around...

I have heard of swapping 05 and up suspension onto older trucks and heard good things about it. Here's the kicker. When we played with an 03 6.0 pulling truck we had no problems with front end hop, had some power hop but got that pretty much taken out after playing with air pressure and truck...

Well I pulled again at another local fair and they wouldn't let me strap the front end. Pulled anyway and ended up blowing out the u-joint that I jsut replaced 2 weeksa ago and took out the yoke on the inner shaft. Anybody know of a better deal than this? I'm going to order one the end of the...

So I tried pulling last night and ended up not making it 3 ft before the front left u-joint let loose and ended up taking out the stub shaft u-joint. Lots of cool pieces on the track. I am trying to put it back together asap. Anybody with any leads on a used unit please hit me up. Rodney...

Anybody else having issues with tuned trucks and cruise control. I took my first long trip after the rebuild on the top end and am having some issues. I have tried KEM 345 tune and it works for a while but if I hit the brakes a couple times or get on it to pass someone it will disable the cruise...

http://allentown.craigslist.org/mcy/2950586820.html Trying to sell my pit bike, Any questions let me know. Thanks Rodney

Posting up for my dad Listing a Kubota RTV 900 for sale. It has less than 300 hrs on it. It is equipped with a hydraulic dump, reciever hitch, roof, bumper Asking $8800 For more information call Terry at (570) 778-2754

Anybody else purchase a set of ported fuel rails off of Elite while they were on sale back at the begninning of december/end of november?

Finally got to installing my rail pressure and fuel pressure gauges this week from complete performance, worked great, thanks guys Also installed a set of Cooper Stt 35 12.50 17s, Way past due for tires and they clear with no rubbing, didn't even have to put the readylift leveling kit on

I got a 4 inch two piece downpipe I bought for doing my wastegate kit, I ended up not using it and going another route. It is new in box, the only thing is that I already drilled holes near the flange to put in cross bolts for pulling/ drag racing applications. I have not welded in the bolts and...

anybody know what size the bolts are for the cab mounts and what the thread pitch is, I want to run a tap up to make sure the threads are clean and put loc tite on the bolts as the front two spun gettin them out. I am at work now and don't remember the size to make sure i have a tap big enough...

Well we started the teardown today, cab is up and the chassis is back to the garage to tear into the motor first thing tomorrow morning.

Trying to clean up around here and listed this on craigslist as well. It is a leer contractors top with a slider window in the front and opening toolboxes on the sides, I have all the keys for the locks and they work. I have no use for this, I would like to get $750 or best offer for it. I am...