Recent content by 08PowerSmoke
-
Anybody in Atlantic beach nc
It sounds like a summer gtg at AB......and we have a DD too!!! Welcome to NC.....- 08PowerSmoke
- Post #18
- Forum: Mid Atlantic US
-
My Build....Finally!!!
Yep I have the Precision 76mm not the Jr's.......I looked on Elites website they don't have the Tow Power X's on there. Go under the Atmosphere section and its there but I have a Factory 59mm VGT hooked to it. Its the ones like Corbin had the first time around!!!- 08PowerSmoke
- Post #15
- Forum: 6.4 Aftermarket
-
My Build....Finally!!!
Well.....Good thing about the tow power X's is it comes with the 76mm from the high powers so all I need is the 62mm VGT valve cover and other lines etc to upgrade..... I think it will run good I have one thing going for me its light weight.....I will have pics up soon I hope!- 08PowerSmoke
- Post #10
- Forum: 6.4 Aftermarket
-
My Build....Finally!!!
Thanks fellas.....Yeah I saw those pistons after the fact :doh:- 08PowerSmoke
- Post #5
- Forum: 6.4 Aftermarket
-
Need help with nos/ for race tomorrow
I need to weigh mine......:thumbsup: What hp do you make on fuel? Just curious......- 08PowerSmoke
- Post #14
- Forum: 6.4 Aftermarket
-
Need help with nos/ for race tomorrow
I would start small like JD said.....are you going to run a button or a progressive set up? I mean if he is spraying that much and you beat him 3 out of 4 times it shouldnt take a whole lot to keep that going.- 08PowerSmoke
- Post #3
- Forum: 6.4 Aftermarket
-
My Build....Finally!!!
Just getting around to putting my build on the forum.......I have a 2008 rclb and still have a little more to do but: STAGE 1<----GETTING DONE NOW 5" MRPB exhaust 4" Downpipe AFE intake w/ Elite tube Spartan tuner ARP head studs OEM gaskets EDE valve springs EDE push rods EDE EGR delete...- 08PowerSmoke
- Thread
- Replies: 15
- Forum: 6.4 Aftermarket
-
-
Which CCV kit to get, MDP, Darkhorse or Elite Diesel?
My choice would be DIY autozone :thumbsup:........but I like the Elite billet unit the most!- 08PowerSmoke
- Post #2
- Forum: 6.4 Aftermarket
-
CCV mod, tie into exhaust, catch can or atmoshere?
Disadvantage of atmosphere......SMELL!!! Just something to get used to but I would do the 45 degree into the exhaust- 08PowerSmoke
- Post #2
- Forum: 6.4 Aftermarket
-
Up pipes
YES it can be done.....the manifolds arent the problem! The 6 bolts that hook the up pipes to the turbo are!!! Take your time and there is a 10mm wrench that looks like a S that will be helpful to get the ones on the bottom. Lots of patience!!! I did mine and ended up getting pissed and cutting...- 08PowerSmoke
- Post #2
- Forum: 6.4 Aftermarket
-
Trans build ???
Interested in this also.....I am going with EDE billet intermediate, input, comp rebuild kit, flex plate and RCD converter! I will hold 700-750HP in my DD but eventually wanna spray it!!- 08PowerSmoke
- Post #4
- Forum: 6.4 Aftermarket
-
Fuel system question
I will post a better list later my parts sheet is with my truck in the garage that should be enough to get you looking though.......they make fittings that are 10AN to 3/8" NPT for the airdog.....I put a guage on the side to measure fuel pressure too! Also look at banjo fittings for the fuel...- 08PowerSmoke
- Post #15
- Forum: 6.4 Aftermarket
-
Fuel system question
THIS IS A START.....WWW.JEGS.COM 4 port Aeromotive regulator: 027-13224.... 183.99 10 feet of 10AN nylon braided hose: 555-110932 ... 69.99 6 feet of 6AN nylon braided hose: 555-110911 .... 39.99 6AN port plug for the regulator 027-15626 .... 9.99 10AN hose end fitting 555-105003 .... 10.99 6AN...- 08PowerSmoke
- Post #14
- Forum: 6.4 Aftermarket
-
Fuel system question
Will do on the pics.....I went the expensive way of course. Nylon braided hose....thread type fittings. Aeromotive everything I could! They even make a fitting that converts the stock HPFP hard line to a AN line.....So no tricks in getting to the HPFP! Just cut the stock line install the fitting...- 08PowerSmoke
- Post #12
- Forum: 6.4 Aftermarket
