Search results

  1. webb06

    07 6.0 starts and immediately dies

    Ya we tried unplugging fan. No change. Have IDS
  2. webb06

    Seat foam questions

    Check with “the seat shop” I assume they have them?
  3. webb06

    07 6.0 starts and immediately dies

    Will start and run 1-2 seconds, if that, and immediately dies like key is shut off. Will restart and immediately die. Found a post on another forum about a pcm/tcm issue causing similar symptoms so I unplugged trans harness and started engine with starter jumper wire and engine will stay...
  4. webb06

    Cruise Control Feature Not Working

    If you’re familiar with Forscan you can disable active cruise control and switch to normal cruise control. That way you wouldn’t have to purchase the active cruise control module and harness. I did this on my father in laws f150 and it works just fine. He bought his truck wrecked and didn’t want...
  5. webb06

    2020 6.7 p00c7 - need help

    Issue resolved with an updated tune based on oem ecu strategy. Sent from my iPhone using Tapatalk
  6. webb06

    EGR delete got me into a little pickle

    I was thinking burn it out with a torch as well Sent from my iPhone using Tapatalk
  7. webb06

    2020 6.7 p00c7 - need help

    2020 F550 6.7 cab chassis P00c7 intake air pressure measurement system fault Boost pressure - a pid reads 56psi Map 14.2 Baro 14.2 Ebp 14.2 Swapped map sensor from another truck with no change. Swapped maf from another truck with no change. Swapped pcm from my dad’s 2021 truck and boost...
  8. webb06

    6.0 Coolant Pressure

    Are you saying it’ll initially build 7 psi then after every hard lull it’ll add onto that and be 14-15psi? Or does it only reach 7psi max at any time? If it’s getting up to 14-15psi it may be popping the cap and releasing pressure Sent from my iPhone using Tapatalk
  9. webb06

    Crank but no start, has fuel

    Does the oil psi gauge on dash come up? Sent from my iPhone using Tapatalk
  10. webb06

    Transmission high temp

    You sure it’s not just a faulty trans temp sensor? Replaced many in the 5r platform Sent from my iPhone using Tapatalk
  11. webb06

    2011 F 250 6.7L Code P1291

    Fixed one the other day. Guy had done an engine swap. When they put the oil fill tube on the wiring harness got pinched under the bolt for the fill tube. Need to check wiring. Or unplug injectors individually and see which one it is. I’ve had injectors cause this code as well. Sent from my...
  12. webb06

    Reflashing an old tuner

    I doubt sct offers support for that old of a tuner. Have you attempted updating using the sct updater software? Sent from my iPhone using Tapatalk
  13. webb06

    6.7 extremely long crank

    Was this a ford contamination kit you installed or aftermarket? Just curious Sent from my iPhone using Tapatalk
  14. webb06

    6.7 extremely long crank

    I still think you need to drive it 10+ miles. I don’t think just idling it is enough to get the air purged. Could be wrong. Sent from my iPhone using Tapatalk
  15. webb06

    PO278 and PO306 codes and smoking

    I suspect cam or lifter failure Sent from my iPhone using Tapatalk
  16. webb06

    Ball joint on the end of the track bar (on the axle.)

    From my experience moog is absolute garbage on track bar joints. Sent from my iPhone using Tapatalk
  17. webb06

    6.4 Blend Door issue

    Should be 4 total. You can do them all with the dash in the truck. Although some of them can be a pain and requires disassembly of some of the piping inside the dash. The driver temp is the one right above the tunnel but can be done with the dash and hvac box in the truck. I’m sure there’s a...
  18. webb06

    A Plea for help..

    If security light is flashing you’ll likely need a PATS parameter reset as well Sent from my iPhone using Tapatalk
  19. webb06

    2006 6.0 block trouble

    Last I saw on YouTube he was in the process of moving to a new shop. So he might be out shop for a while. Just searched his videos. Look at “mikes refresh job” from about 2 years back and it shows the tools to do rod bushings Sent from my iPhone using Tapatalk
  20. webb06

    2006 6.0 block trouble

    I know Anthony at super duty service in kc replaces rod bushings in 6.0’s. Look through his YouTube videos and you’ll see him talking about them. He had a special tool made to be able to remove and install them. Sent from my iPhone using Tapatalk

Random media

3DA5AC75-B2F6-4464-9BEF-05ED5099C68F
ImageUploadedByTapatalk1367426129_317571
eleanor_part_two_42_
6.7
truckin
IMG_2348
20220319_092608.jpg
1291077660147
75295_123503404375468_100001474272705_142240_3478230_n
IMG_0382
IMG_0054
photo_2_3

Latest posts

Members online

No members online now.
Total: 2,226 (members: 0, guests: 2,226)
Top