Search results
-
-
3.5" coil spring spacers
Hey guys Looking for a pair of 3.5" spacers.(possibly consider 4") Have cash ready to buy- BigRed97
- Thread
- Replies: 0
- Forum: Want to Buy
-
-
Fuel distribution to back of the heads
I believe it they are -6 ORB but its been a few years since I was back there- BigRed97
- Post #23
- Forum: 7.3 Aftermarket
-
05+ axles and brackets for conversion
I do not have: New steering linkage ends brake calipers(both axles) Radius arms(I was going to 4 link) Track bar ball joint And I'm sure there are some small incidental items i don't have At this point on going to hang on to the stuff until spring- BigRed97
- Post #10
- Forum: Suspension and Related Parts
-
97 7.3 skipping, losing power
Oh and a quick comparison test showed equal compression in cyl 1 & 3- BigRed97
- Post #6
- Forum: 94-97 Tech
-
97 7.3 skipping, losing power
According to the ICP readings via scan tool its around 600@idle with ~13% DC and (when it runs) at 1500rpm its about 1600psi with ~17-20% DC When cranking(very extended) it will climp all the way up to 3k psi with ~45%DC before it fires We are going to get a mechanical gauge on it as soon as I...- BigRed97
- Post #5
- Forum: 94-97 Tech
-
Fuel distribution to back of the heads
I would swap to a Y block instead of the T fitting. Smoother flow of the fuel means less chance of aeration I used a Y block bolted to the bosses for the old mech fuel pump then out of the Y to the back of the heads via DI fittings Here a few pics And no where near the up pipes...the...- BigRed97
- Post #17
- Forum: 7.3 Aftermarket
-
05+ axles and brackets for conversion
At this time they are no longer for sale unless someone wants the ENTIRE package- BigRed97
- Post #7
- Forum: Suspension and Related Parts
-
05+ axles and brackets for conversion
Ok sounds good- BigRed97
- Post #5
- Forum: Suspension and Related Parts
-
05+ axles and brackets for conversion
Well I need the stuff gone....maybe we can work out a package deal if you're interested- BigRed97
- Post #3
- Forum: Suspension and Related Parts
-
05+ axles and brackets for conversion
pair of SRW axles out of an 06, 3.73 gears. told 65k miles from salvage yard i got them from. the front has, already installed: 4 new ball joints, 1 new hub and ujoint, 2 new axle dust seals(updated metal ones), 2 new hub seals,2 new rotor dust shields, new rotors and pads included (no...- BigRed97
- Thread
- Replies: 10
- Forum: Suspension and Related Parts
-
Traction Blocks installed!
Trevor. I got them about a week or two before installing them, so early March (possibly last few days of Feb) Couldn't be happier with they way they perform and look. And I'm still planning on ordering front suspension stuff from you, hopefully soon . I'll try to snap a few pics of them...- BigRed97
- Post #5
- Forum: Precision Metal Fabrication
-
speedometer inop..
Possibly. That was actuallyy first thought due to the whole hitting the dash to make it work But I had checked and spread, for better contact, all of the pins on all three connectors with no change -
speedometer inop..
Alternator had been replaced in the middle of this(for unrelated issue) with no change -
speedometer inop..
I have it written down some where but Thursday morning I pulled it apart again and checked every segment of wire from the abs module to the cluster and every wire checked good. No corrosion anywhere . So I put it back together and now it works again -
-
speedometer inop..
I checked that ground. It was clean and tight, but I pulled it off anyway cleaned it and reattached. No change Thoughts? Anyone know what the VSS+ signal at the cluster should be? -
-
speedometer inop..
hey guys, im a little stuck on this. my speedo doesnt work. it started a few years ago: sometimes in the morning the speedo wouldnt work, id give the top of the dash a little smack and it would come to life and be fine for a couple days or even a week or so. it was like this until about a month...
