Search results

  1. O

    04 6.0 No Start. New HPOP

    Yeah I haven't been able to find a good way of whether the pump is building pressure or not.
  2. O

    04 6.0 No Start. New HPOP

    It's like dead in the middle. Some things on mine are early 04 style some are 04-07 style. Like my oil rails don't have the braided lines running to them. They're the standpipe style.
  3. O

    04 6.0 No Start. New HPOP

    So I'll hopefully get it to run for more than a week!
  4. O

    04 6.0 No Start. New HPOP

    Found my issue. I can tell I do this too often cause A) all the bolts to get to the HPOP were still not too tight to have to use a breaker bar and B) I got to the HPOP in about 35 from fully assembled. When I put the HPOP in I put the yellow o ring on the bottom like you're supposed to but I put...
  5. O

    04 6.0 No Start. New HPOP

    Took in the IPR Valve and the guy just handed me a new one and took mine. So that was easy. Then I tried to test the new one this morning, installed it in the truck and am building 6 ICP on 84.7 IPR... so this didn't solve my problem. Could it be branch tubes? What's the symptoms for branch tubes?
  6. O

    04 6.0 No Start. New HPOP

    I might do that. I'm not sure yet. I have a 79 to drive so I might just drive that till I find out if they are going to refund me or not unless they make me buy a new one
  7. O

    04 6.0 No Start. New HPOP

    Sounds like they're waiting to see if it's faulty maybe I can see if they can at least test it there and make sure it's faulty. He said they'll send it in and I can get a new one and they'll refund me if it ends up being faulty
  8. O

    04 6.0 No Start. New HPOP

    Sorry to keep carrying on with my own post but the guy at Ford said that he can go ahead and take it in and they'll do a warranty claim and if it's faulty then they will give me a replacement
  9. O

    04 6.0 No Start. New HPOP

    K tested the IPR Controller hooked to both batteries on the 6.0 after I cleaned it out and was able to move the valve by pushing it down on a bolt, got nothing. Then I tried it on my 79 f150 that I daily drive and it still wasn't move the IPR. Is it possible it went out within the matter of like...
  10. O

    04 6.0 No Start. New HPOP

    Pulled the IPR Valve out. Hooked it to the OTC IPR Controller. Controller said it was getting 12V Input and IPR Output light was lit up and the IPR Valve did nothing.
  11. O

    04 6.0 No Start. New HPOP

    yeah but I'm wondering if it got filled with dirt or something in the oil system when I had the valve covers off doing the injectors. I'll pull it out here in a minute.
  12. O

    04 6.0 No Start. New HPOP

    K finally got around to air testing it. I put 140psi to it and heard an air leak on the drivers side so I popped the valve cover, the air tones didn't change whether I closed the IPR Valve or not. I was using the controller that you buy from otc. While air testing with the valve cover off I...
  13. O

    04 6.0 No Start. New HPOP

    Yeah I used the HPOP from the dealership. I ordered that tool that closes the IPR valve for you and am going to buy the fittings for the icp sensor port. Then I'll air test it that way
  14. O

    04 6.0 No Start. New HPOP

    Update. I pulled the oil filter and held the drain plug down. The housing seemed to fill pretty quick. The oil pressure on the gauge seems to fluctuate between the top of the L and bottom of the L when cranking though it never builds to normal oil pressure while cranking. Even though the pump is...
  15. O

    04 6.0 No Start. New HPOP

  16. O

    04 6.0 No Start. New HPOP

    Well put all new injector seals, o rail nipple cup seals in it and it started. One injector was really toasted and I'll post a picture of it here in a minute. So I had to buy one new injector but the others I was able to replace the seals and get it to build enough pressure. After I started it...
  17. O

    04 6.0 No Start. New HPOP

    Yeah I ordered the injector seal kit, o rail nipple cup tool and 8 new nipple cups
  18. O

    04 6.0 No Start. New HPOP

    They were. I'm just going to pull the rails and do a top o ring kit on it myself
  19. O

    04 6.0 No Start. New HPOP

    Yeah $2k for one side
  20. O

    04 6.0 No Start. New HPOP

    How involved is it to do myself. I've rebuilt a handful of old ford gas engines

Random media

he351ve T4i turbine inlet
41F1BDB1-5322-46C8-ADA7-4CFAEF323BB2
024
20120414_134419
2011-07-06_22-25-01_636
PART951319154316768
IMG_0320
image103
IMG_0065
10.25 carnage
20121013_131825
image38

Latest posts

Members online

Total: 655 (members: 1, guests: 654)
Top