Search results

I have a 2015 350 cclb 4x4. Is what you have meant to be "lifting blocks"? I'm wanting to replace the 4" blocks with the factory 2" blocks to bring the rear down.

Looking for a pair of F250 rear blocks (2 inch), preferably with U-bolts. Need to be "reasonably" clean, not rusting to the point of falling apart.

I have to believe swapping a supercab will be the same process I did here with the regular cab. The area to measure is how far back the engine is set in the 93 versus the 75. I never measured with this project, but with the firewall work I had to do, I believe the 70's trucks had the engines a...

I'm in the process of swapping a 1963 International V-liner onto a 1984 International S1900 chassis with the DT466. I found the 84 cheap but preferred a 1993 to 1995 which has the "P" pump (last years of the mechanical injection engines). 84 to 92 were the years of the inline MW pumps which are...

ok. sending a PM

If you're needing a track bar mounting bracket let me know, I have a spare from my swap I did a couple years ago. I designed a bracket for the 96 truck I was working on and made two at that time. It's beefy, constructed from 3/8 and 5/16 material. It attaches to the frame rail and the engine...

Thanks. Looking for several, so if anyone else has one please reach out.

I'm really just looking for the large brass plug that holds the spring/valve in the regulator and the shrader valve. Anyone have old fuel bowls laying around with the pressure regulators still attached?

I have a used one from a 96 that had 170K miles. Tank is fine, just didn't use it as part of the engine swap project. I used a SD tank instead due to space constraints. Tank fits in a large flat rate box so $20 for shipping and $20 for the tank?? I'm 4 hours by car from you so if I have it in...

I do have a pair of the brackets. Make an offer plus $15 for shipping USPS flat rate.

The valve cover has a small blemish in the rear corner (see pic). I'll look tomorrow for engine mount brackets. I'm assuming you're asking for the brackets that bolt to the block and not the "rubber'd" motor mounts.

bump. still have everything. offers?

Two engines worth of parts, prices include shipping: 96: - Forged rods, $225 - Front cover, $250 Late 97: - Forged rods, $225 - AB injectors, $225 - HPOP, $150 - Front cover $250 Also have 2 turbos, many sets of used but clean up pipes, several collectors (baby butts) and other parts. Make...

Thanks guys. Yes, the odometer is completely functional. I swapped the 05 sensor in the rear axle with an OBS sensor and both speedo and odometer work normally. I'm finishing up the dash details now (wiring and vacuum lines) and then I'll get the floor cover down, bench seat back in and doors...

Here's the finished installation.

Inching along with this project still. Just finished the gauge cluster and wiper switch. I used the case of the original wiper switch and "grafted" the OBS switch to it and it works great. I did the same with the OBS gauge cluster and the 78 bezel. It was alot of plastic trimming of both the 78...

Working on two 96 trucks. I need 3 front turn signal socket with several inches of wire and I also need a bed wire harness (connector plug to stop/backup lights, sockets, etc).

Well the heater/AC box didn't fit like I expected. I "trial fit" everything a few months back and it seemed like it was good to go. Naturally after wrapping it up clean and tight in insulation is when I discover it doesn't fit :( The problem is clearance around the valve cover. I had to cut a...

I was finishing laying the sound deadening on the floor and firewall when I realized it was somewhat a pointless exercise if I didn't also cover the heater/AC box. The box fits into a HUGE gaping hole in the firewall and is just (most hollow) plastic. All the floor covering I could add wouldn't...

Making good progress with "re-wiring" the inside of the cab. Normally I would keep the original trucks wiring harness for lights, gauges, horns, wipers, etc but this 78 truck was missing most of it's wiring when I got it. Typically I just cut down the mid-90s harness to be a "stand alone"...