Search results

I'm looking to do some r an d of my own and would like to see if anyone has the stock intercooler pipes they wouldn't mind shipping out.

Shot in the dark here but trying to find the previous owner of this truck. I'm in pa lola like truck came from nj https://www.allentownkia.com/auto/used-2013-ford-f250-super-duty-platinum-allentown-pa/24454380/ Its ******d and has no tuner with it so was gonna take a shot finding previous...

Does anyone make a plug and play remote start with mini.al splicing that you know of?

are there any remote starter plug and play systems out there with minimum splicing.

any one have one for sale?

I need the stock spring for fuel regulator for 6.0 powerstroke. I am running a new pump and the blue spring put me at 85 psi base

I'm trying to replace the stock unit and retain the factory lines an regulator. I can't seem to find 1/2 female push on to 3/8. Or some variant I can make them work. Anyone ideas or part numbers to retain factory line. Also can the return side of the pump just be bypassed and run a coupling to...

vt365 main bolt sequence says to start 1 inner the 2 inner then 3 outer opposite and then 4 outer ford manual i have says 1 inner 2 same side outer then 3 inner 4 outer same side. if this makes sense. sorry hard to explain in words. i broke a main bolt torquing to 170ftlbs final using ford...

hey guys, I have confirmed I have a slight head gasket leak and I'm pulling the engine. I'm trying to get some insight with those who have done the same and what you replaced while doing so. I am going to check the heads for warping and cracks but I'm thinking other parts of the engine that...

Was wondering if I splice a 6.4 harness in will the 6.4 fuel pump drop in Stock 6.0 pump housing. And if so would there be any gains with the smaller lines from the 6.0 housing vs 6.4. I know i can put the entire 6.4 hfcm in but was trying to go a cheaper route for now. im running 190/stock...

I have a code P0263 cylinder 1 injector circuit contribution failure/balance failure. i took all 8 injectors out while studding got everything back together and seem to have something bad. ICP and duty is good. truck smooths out on rev just rough idle and stumble from the start. but these...

Looking for 21k obo I'm located in Bethlehem PA 18020 You can contacte.personally through add or pms. Any questions ask http://allentown.craigslist.org/cto/5374230110.html

Looking at a 16x12 micky tompson wheels. I have 2000 f250 with 2.5 inch lift springs. I am wondering on whats the largest tire i can run. I have seen on the forum 33x15.5 (aka 375/55) fit with trimming a tad but I am wondering if 35s would work that wide as well or of anyone has done this...

I was coming off a 16 hour shift started my 2000 7.3 up let it idle for about 15-20 min to get warm like i always do. (BTW truck ran fine before work it was about 26 degrees) Get in start to drive it and it has a bad buck and chug to it. finally about 1 mile down the road it dies completely. so...

have a 2000 f250 with Harley Davidson in now. i want to upgrade to a projector with hid setup for a crisp light as i do most my driving at night unfortunate. so ebay? or and one know where to point me for a good quality product. also was interested in dual beam seemed like a great over kill...

2000 f250 2.5" rc leveling kit. Will these sizes fit with little trimming and or rubing 20x12 wheels with -46 offset - 35x12.5 m/t 20x10 wheels with -24 offset 35x12.5 m/t Looking for people who have run them in the 99-04 trucks seems to be popular but hard to tell on lift size at pictures...

looking for a nice wheel tire combo with a deep dish that will fit 99-04 f250. most are all for 05 and up so if you have some message me or text 86three-51four-323four located in east pa ,near jersey, new york thanks