Search results
-
Posts
I'm gonna quit posting here. Nobody hardly comments. Thks Sent from my SM-S906U using Tapatalk- prefab221
- Thread
- Replies: 3
- Forum: 1999-2015 Superduty Series General
-
Pedal Commander
Is this all what they claim it is? Saw it on Amazon.com.. $300. Sent from my SM-S906U using Tapatalk- prefab221
- Thread
- Replies: 10
- Forum: 1999-2015 Superduty Series General
-
OEM vs NAPA: BRAKE ROTORS '16 F250 PS
Anyone? Sent from my SM-S906U using Tapatalk- prefab221
- Post #2
- Forum: 1999-2015 Superduty Series General
-
OEM vs NAPA: BRAKE ROTORS '16 F250 PS
Does anyone have experience with NAPA front brake rotors? Are they better than OEM? The cost more, just wondering are they better. Thank you Sent from my SM-S906U using Tapatalk- prefab221
- Thread
- Replies: 2
- Forum: 1999-2015 Superduty Series General
-
Death wobble while braking: my 2016 F250 is getting loose. When hard braking at 65 mph .
TOP QUALITY REPLACEMENT ROTORS? Sent from my SM-S906U using Tapatalk- prefab221
- Post #7
- Forum: 6.7 Tech & FAQ
-
Death wobble while braking: my 2016 F250 is getting loose. When hard braking at 65 mph .
Ty Sir, i will ck them this weekend. I bought a new set of Detroit axle rotors, maybe they are junk? Probably go with fomoco rotors. Im not hard at all on the truck... Sent from my SM-S906U using Tapatalk- prefab221
- Post #5
- Forum: 6.7 Tech & FAQ
-
Side avoidance system
Can you get a side vehicle avoidance system for a 2016 f250? Thank you Sent from my SM-S906U using Tapatalk- prefab221
- Thread
- Replies: 1
- Forum: 1999-2015 Superduty Series General
-
Death wobble while braking: my 2016 F250 is getting loose. When hard braking at 65 mph .
I had replaced the trac bar joint about 2 months ago. Sent from my SM-S906U using Tapatalk- prefab221
- Post #3
- Forum: 6.7 Tech & FAQ
-
Death wobble while braking: my 2016 F250 is getting loose. When hard braking at 65 mph .
2016 F250 w 236,000 mi. When braking hard at 65 mph im getting a bad wobble... alignment shop says it needs tie rod ends, could this be the problem? I put new front rotors and pads recently. Any ideas? Thank you- prefab221
- Thread
- Replies: 7
- Forum: 6.7 Tech & FAQ
-
2016 f250 167,000 mi.
What is a good brand of scan tool ? Sent from my SM-G986U using Tapatalk -
2016 f250 167,000 mi.
The truck is 100% stock Sent from my SM-G986U using Tapatalk -
2016 6.7 powerstroke
Just as a preventive measure. Sent from my SM-G986U using Tapatalk -
2016 f250 167,000 mi.
Does anyone know what controls turbo boost? Sometimes when I full throttle I get more boost than other times. If I shut the truck off at a light and back on its runs with alot of boost. I can't figure it out . Also getting a loud whooshing noise. Thanks. Sent from my SM-G986U using Tapatalk -
NEW MEMBER HERE IN TEXAS
Nice to be here. 2016 f250 powerstroke 167,000 miles. Sent from my SM-G986U using Tapatalk- prefab221
- Thread
- Replies: 1
- Forum: Newly Enlisted
-
2016 6.7 powerstroke
Installed the new ca tube . Didn't change anything, the problem still exists. Sent from my SM-G986U using Tapatalk -
2016 6.7 powerstroke
I talked to fomo yesterday and it is probably the cac tube has cracked.... gonna ck it out, $135 part Sent from my SM-G986U using Tapatalk -
2016 6.7 powerstroke
Would that make it run like a bat outta he'll? Engine and trans temp both at 198 +/-. Sent from my SM-G986U using Tapatalk -
2016 6.7 powerstroke
I don't know yet. Should be at the dealer jan 2nd Sent from my SM-G986U using Tapatalk -
2016 6.7 powerstroke
My truck has 167,000 mi. On it. Running good until yesterday. Starting hearing a roaring noise under acceleration.kinda sounds like a big shop vac. Best I can tell it's coming from the rear of the motor. Drove it easy home and when I got there ,there was no more noise. Everything was normal...
