Recent content by 01REDSTROKER
-
0
What's everyone done for seats?
I just looked and you are right. I have only used them for superduty stuff only, but was told about them from a guy that drove and had them in his obs. The web site is kinda new so might have to call them.- 01REDSTROKER
- Post #4
- Forum: 94-97 Aftermarket
-
0
What's everyone done for seats?
This place has oem quality seat cusions and leathers. www.theseatshop.com- 01REDSTROKER
- Post #2
- Forum: 94-97 Aftermarket
-
0
4r100 help/ weird shifting
My dads 4r100 would lock up very hard and after about a day of that it wanted to start out in 2 gear. It had codes but I don't remember them. Installed a new vb and it was still doing it. Some one said change out the pcm, so we did....fixed all the issues and that was two years ago.- 01REDSTROKER
- Post #11
- Forum: 7.3 Tech
-
0
6.0 chugging gray smoke
It started before the injector change. It is just worse after. I ordered new o rings and copper washers as well as a oil rail rebuild kit. Going to see what that does.- 01REDSTROKER
- Post #10
- Forum: 6.0 Tech
-
0
6.0 chugging gray smoke
swinky. yes the ipr% is high when it is trying to idle. i must have a hpo leak. lassie. yes injector o-rings and washers are new. i am trying to figure out if the nipple that comes out of the fuel/oil rail ever fails. on the other two trucks i did injectors on i do not remember the nipples...- 01REDSTROKER
- Post #8
- Forum: 6.0 Tech
-
0
6.0 chugging gray smoke
yes before i pulled the injectors the truck started great just blew white fuel smoke and had a bad idle. now it is really hard to start and blows more tones more gray/white fuel smoke. do the O-rings in the fuel/ oil rail ever go bad (where the stem comes out for the injector) i ask because the...- 01REDSTROKER
- Post #5
- Forum: 6.0 Tech
-
0
6.0 chugging gray smoke
I have a injector 1 low code. I don't have the code with me right now. All of the injectors got sent to warren diesel for a rebuild. All have new nozzles. I was watching the icp today and the ipr has to close and then it will build hpo but take a lot of turning over all most to the point of...- 01REDSTROKER
- Post #3
- Forum: 6.0 Tech
-
0
6.0 chugging gray smoke
just a little back ground info. 2005, deleted 6.0. no tuning good ficm voltage truck ran great, not issues other than a minor case of sticking spool valves that rev-x took care of. Drove truck about 100 mi. home, let it idle while i unloaded gear.(no issues) next morning went to leave, started...- 01REDSTROKER
- Thread
- Replies: 9
- Forum: 6.0 Tech
-
0
parting out 06 F350,6.0,4x4,auto,63k miles
do you still have the trans? pm sent-- 01REDSTROKER
- Post #37
- Forum: Engine and Drivetrain
-
0
6.0 Trans help
went out and started it and it goes in to gear and moves like it should. going to pull it up to the shop and pull the pan.- 01REDSTROKER
- Post #4
- Forum: 6.0 Tech
-
0
6.0 Trans help
Where would I find the flow chart. I searched the codes but did not come up with much.- 01REDSTROKER
- Post #3
- Forum: 6.0 Tech
-
0
Runs great 6.0l engine and trans/transfer case
Do you know anything else about the trans? I am interested in it and i am not to far from you.- 01REDSTROKER
- Post #9
- Forum: Engine and Drivetrain
-
0
6.0 Trans help
went to pull into my parents drive way and the truck would not move. It acted like it was in 4th, and the tow/haul light started flashing, so i backed up and drive about 1/2 mile to my house and pulled the codes; p0766 and p2703. Trans fluid only has about 3000 mi on it and looks good. after...- 01REDSTROKER
- Thread
- Replies: 4
- Forum: 6.0 Tech
Members online
No members online now.