Recent content by 95-F-2FITTY

Wiring gremlin please help!

Is that swap suspose to be plug and play or is a automatic pinned out different in the firewall 76 pin connector?
- 95-F-2FITTY
- Post #2
- May 8, 2014
- Forum: 94-97 Tech
Wiring gremlin please help!

I have swapped the dash and harness out of a 96 PSD Into my 95. Everything works as should except for my wipers. When I turn my key to the "start" position not the spot where you leave it when its running but the spot that makes the engine turn over my wipers start working. I tried unplugging my...
- 95-F-2FITTY
- Thread
- May 7, 2014
- Replies: 3
- Forum: 94-97 Tech
Shakeyand Rough idle when warm

No it sure did not but i got pissed and threw a new one on it and that straightened it out idles smooth again. So i guess what i learned is just because the sensor dont have oil in it doesnt mean it cant be bad lol
- 95-F-2FITTY
- Post #3
- May 1, 2014
- Forum: 94-97 Tech
Shakeyand Rough idle when warm

Well i have put new injectors in my truck, cleaned the ipr and tried unplugging my icp sensor to see if it helped my rough idle and it has not. My truck runs fine when it is cold or has set all night ,but once it reaches operating temp it starts to have a rougher shakey idle. Any ideas as to...
- 95-F-2FITTY
- Thread
- Apr 17, 2014
- Replies: 3
- Forum: 94-97 Tech
POWER-STRUCK Tunes

Well i got my 180/100's and my chip back all i can say is WOW! Justin is a great guy to deal with ,awsome customer service and i couldnt be happier with the injectors or tunes!
- 95-F-2FITTY
- Post #80
- Apr 14, 2014
- Forum: 7.3 Aftermarket
POWER-STRUCK Tunes

When did you send yours in? Do you know the turn around time on them?
- 95-F-2FITTY
- Post #66
- Mar 31, 2014
- Forum: 7.3 Aftermarket
POWER-STRUCK Tunes

I ordered a set of 180/100's and i sent him my ts for tunes. Cores arrived a week ago i will post my results when i get them and put em in!
- 95-F-2FITTY
- Post #64
- Mar 31, 2014
- Forum: 7.3 Aftermarket
Shaking lopey/missing at idle

Because it passed the buzz test but i havent ran the cct yet i will let you know what happens.
- 95-F-2FITTY
- Post #9
- Feb 20, 2014
- Forum: 94-97 Tech
Shaking lopey/missing at idle

Run a cct?
- 95-F-2FITTY
- Post #7
- Feb 20, 2014
- Forum: 94-97 Tech
Shaking lopey/missing at idle

My Truck has 169,000 on it and as far as i know the injectors are stock except for one of them that i replaced.I unplugged the icp and it didnt do anything. But my oil pressure gauge is reading normal the other day it was reading lower than normal but i unhooked the sensor and plugged it back in...
- 95-F-2FITTY
- Post #4
- Feb 19, 2014
- Forum: 94-97 Tech
Shaking lopey/missing at idle

Like stated my truck is shaking and it sounds like a miss or a lope at idle. When its cold its fine and doesnt do it. Also when im driving down the road under throttle it seems to run fine. Its only at idle or up to a quarter throttle and it shakes when it is idling. I cleaned the IPR, and the...
- 95-F-2FITTY
- Thread
- Feb 17, 2014
- Replies: 8
- Forum: 94-97 Tech
Heater not warming up!

i pressure tested the cap and it tested all the way to 16 psi it is not leaking coolant anywhere either.
- 95-F-2FITTY
- Post #14
- Jan 10, 2014
- Forum: 94-97 Tech
high idle?

my truck will idle up around 900 rpm for a few minutes when i first start it.
- 95-F-2FITTY
- Post #14
- Jan 10, 2014
- Forum: 94-97 Tech
Heater not warming up!

Ok i checked the temp door and it is working full motion. Is the blend door the one that is located under the hood on the firewall?
- 95-F-2FITTY
- Post #12
- Jan 3, 2014
- Forum: 94-97 Tech
Another 7.3 hp thread , how much does it really take?

Yeah it blows:P Sent from my SCH-I535 using Tapatalk
- 95-F-2FITTY
- Post #46
- Dec 21, 2013
- Forum: 7.3 Aftermarket