Recent content by stillbuildin

  1. S

    Torque Pro app WARNING!!

    Thanks, that'd be great to have!
  2. S

    Torque Pro app WARNING!!

    UPDATE: Got the truck to start, same issues and same codes but while running I pulled the harness plug off the driver's side uvch. No difference in running. So it's now running on the one bank only - makes sense I guess in view of the 1271, 1273, 1275, 1277 and 1294, 1296 codes. With the...
  3. S

    Torque Pro app WARNING!!

    It's the elm 327 mini, made by konnwei. I did test it with Car Diagnostic Pro (because it won't work with Car Gauge Pro), and it failed some tests. I guess not fully obd2 compliant.....was gonna buy the bafx one instead.
  4. S

    Torque Pro app WARNING!!

    Yes, although I never got it set up right. The only gauge responses it showed were revs and boost, I think. I put all the gauges on screen for injector pressure etc, but they all read zero, even when the truck ran fine - before torque shut the motor off.
  5. S

    Torque Pro app WARNING!!

    I guess I'll start ohming from the idm to injectors if all else fails
  6. S

    Torque Pro app WARNING!!

    Ok so I hooked up their batteries again, no start. It's the same because it'll run for a couple seconds very rough and set the cel. Then quit. It's cold but I had it also plugged in for three hours. I guess whatever happened had now become permanent........I'll leave it plugged in overnight see...
  7. S

    Torque Pro app WARNING!!

    Oh, and it's an 02 truck
  8. S

    Torque Pro app WARNING!!

    Thanks for all the input, much appreciated! Sure, I agree that there should be no way the app could cause this but........for the motor to run in a way I've never seen before - right after restarting from the app shutting it down, is hard to ignore. It doesn't shake like when you have one bank...
  9. S

    Torque Pro app WARNING!!

    Hi all, I bought the elm dongle and torque pro. Plugged it in and connected to the app. Started the truck to get input and accidentally hit the dtc scan menu. It shut the motor off so I disconnected the Bluetooth. Restarted the truck it's suddenly running rough, no power and cel on. No codes on...
  10. S

    Strange Starting Problem??

    I tried a buddy's Innovo scanner, showed nothing. I've ordered the Bluetooth dongle to use with my android - should be here in the next week or so :) I didn't know I could monitor icp on it, that'll be great! I'll learn the device and report back. Thanks again for all your input!
  11. S

    Strange Starting Problem??

    Thanks all for this info, really appreciate all the input! Justin, yes the hpop level is good before starting. Although I've just noticed the icp plug is full of oil! But if I unplug it, it makes no difference to the truck starting.....
  12. S

    Strange Starting Problem??

    Couldn't see any white smoke at all while cranking......?
  13. S

    Strange Starting Problem??

    So, volts are at 12.45 first, they drop to 11.7 when the key is turned on to warm up the glowplugs. It then drops to 10.54 when cranking.......?
  14. S

    Strange Starting Problem??

    Oh gotcha, Amsoil synthetic. Sounds like a plan......
  15. S

    Strange Starting Problem??

    So should I bother with the 5 40 or just change it now to 15 40 Amsoil? Synthetic?
See more

Random media

sept_29_10_1691
Misc_040
FB_IMG_1524919680474
2011-05-31_17-20-35_79
Capone
suicide_gun
Uniden_PC68LTW
2.6 truck
Out with the bad in with the good.
IMG_2394
vg_f150_1
Ranger Z520

Latest posts

Members online

Total: 778 (members: 1, guests: 777)
Top