Search results

  1. oneturboforme

    WTB: 250/200 Full Force Injectors for 7.3L

    I've got a set of 300/200 full force I bought from vision diesel that I will sell ya. One injector has a stuck poppet valve but you can send them in to get it fixed shouldn't be an issue
  2. oneturboforme

    No start no smoke

    Pulled the driver side and sure enough oil is pumping out of an injector. It's the poppet valve tho not the oring. Pulled the solenoid off felt with a feeler gauge around had one little catchy spot bUT once I wiggled the gauge around it went away. Clearance is .008 on it. Reinstalled it. It is...
  3. oneturboforme

    No start no smoke

    Well it was a colder morning around 45 and I went out and it started within a second of cranking. Well now I'm thinking injector orings even tho there brand new. I did get 2 full turns on the idm harness bolt before hand. I'll drive it around let it get hot and report back I'm really hoping it's...
  4. oneturboforme

    No start no smoke

    I half ass checked the looms one thing that did seem odd my map and ebp showed 97kpa sitting there not running if I started it and gave it some peddle it moved to 103. So I thought it was good but now I read that the map ebp and ipr all have the same supply. Is this correct?
  5. oneturboforme

    No start no smoke

    Only consistent one is p0605 with my chip installed, once in awhile will get a p1212 and p1280 but it seems like it's rare and only in memory codes. It's weird the fact it's not even smoking
  6. oneturboforme

    No start no smoke

    Replaced my injectors hpop springs pushrods studs. Anyways seemed to start up fine at first. It was idling rough so I took it for a 90 mile trip still had a funny miss. Thought it was a tuning issue no big deal shut the truck off. Couldn't get it started cranks but no start. Pulled the chip...
  7. oneturboforme

    starter locked up??? help

    Starter is toast. If the battery's are dying and it cranks so it's hard on them. Also next time I suggest getting a wrench and spinning it over by hand like suggested or you might be in for one or two rods if somehow your injector in leaking
  8. oneturboforme

    79 crew cab build

    Well it will never be the fastest 6.0 but it might have the most room under the hood out of all of them
  9. oneturboforme

    mellino lpop gasket

    Here are some pictures of what I'm taking about.
  10. oneturboforme

    mellino lpop gasket

    Well I ordered a lpop off the net. When it got here the package was beat to piss. To the point where the instructions with it are shredded. I'm looking at the gasket that replaced the orange factory o ring, it's square. But it is also cut but it's at an angle almost like it suppose to be. Does...
  11. oneturboforme

    Pro Stock Powerstroke Mustang

    I'm not trying to throw this thread even more outta wack but didn't a mecanically injected 7.3 make over 1500hp and I think it was using a stock crank. And come on 300hp.. lol give the 7.3 some more credit than that there are a lot of guys 700 on fuel on stock forged motors and some spraying...
  12. oneturboforme

    intermittent wipers don't work

    Truck a 07 and I cannot get the intermittent wiper to work I don't have a owners manual so I can't check fuse location. Does the gem control the intermittent or is there another box? And if so where the hell is it. Thanks Guys I'm bashing my head against the wall and I deal with control wiring...
  13. oneturboforme

    79 crew cab build

    Got the dash mounted still need some timing here and there but it actually went in pretty easy.
  14. oneturboforme

    All those from Montana... Post up!!!

    Gonna be moving to medicine lake here in about a week. Hopefully it's far enough away from bakken to not see to much ruckus
  15. oneturboforme

    valve shims

    Think it's all comes down to trial and error and a lot of these guys are putting so much time to see what combos work the best. Like swamps or irate just to name some. Have there comp. springs I mean if they spent hundreds of hours and thousands of dollars why would they come out and say o you...
  16. oneturboforme

    Ford grey gasket sealant

    That gray sealant works really good. I know I used it on my intake plenums and they don't leak only thing is when you want to pull them out it turns into a pita
  17. oneturboforme

    valve shims

    To tell you the truth I have been thinkin about that but in all honesty my motor has 190k on it with a 468 I'm sure I'm on barrowed time. I'll make sure the one on the stand get the better springs. And quite honestly I just don't run it hard. It's a 5 speed so I never race it I might roll on it...
  18. oneturboforme

    oil pressure gauge

    I'd be leary of the gauge on the dash my obs always reads between r and m in normal. But my autometer varies from 42 to as low as 6 (my lpop is going out)
  19. oneturboforme

    valve shims

    I have the shim pack from comp sitting here.
  20. oneturboforme

    SRP1.1 strikes again

    I had a salesmen say to me "well if it(srp1.1) does go out atleast it's JUST brass and not steel shavings going through your hpo system" hahaha wtf is that? I went with duals just for the reliability of it. Not saying others singles aren't reliable just now I have to **** up two instead of just one

Random media

IMG_20130328_202212_367
hx40 over 38r
169815_1660981239184_1076760051_1781960_6725912_o
O&G's 2011 F250 Journey
5682441D-61ED-4083-8FB8-F2D92B56FDA7
2008 King Ranch motor work
My Toys
Kardashians
2013-03-21_18-00-02_49
maple_grove_013
intake elbow upgrade
2013-02-12_14-57-48_87

Latest posts

Members online

No members online now.
Total: 625 (members: 0, guests: 625)
Top