Search results

Looking for a set of 17x10s. Would prefer Weld Cheyenne, Velocity, mountain crusher, or Sandstorm, but let me know what you got. I can go up to 12 wide, but no narrower than 10 wide.

Im having an issue getting the speed input on my PCS working. I have it wired to the VSS sensor and my speedometer in the dash is working. The 2 wires for the PCS are labelled "vehicle speed sensor" and "sensor ground". So since the VSS doesnt have a sensor ground circuit, i ran the sensor...

Was almost finished rebuilding my Dana 60 and hit a snag. I replaced the inner axle seals and the axle shafts will not go back through the new seals. Has anyone run into this issue? I used Dana/Spicer 52148 seals. I went to the Ford dealer today to see what seals they offer for it and they are...

I have a set of stock AA 7.3 injectors. They have 290k miles on them and one of them did have a bad copper washer allowing exhaust to blow past it which covered the injector below the bottom o-ring. No soot blew past the bottom o-ring and should not have gotten into the internals. The engine did...

Does anyone know whether or not one would be able to fix curb rash? I'm looking at a set of 20x10 Weld Cheyennes. I can get them uber cheap, but every single one of them have curb rash pretty bad. Any ideas?? Sent from my SAMSUNG-SGH-I337

Helping a friend clear up some shop space. Most parts are used. He installed most of this stuff on his truck and decided he wanted to take it all back out and redo it using mostly destroked parts. $600 OBO for everything. I would like to get rid of everything together. Some of this stuff...

I just wanted to drop in and say thanks for the great service, parts, and quick shipping. I called Dan last Thursday about a range shift fork I needed for a BW1356 t-case in a Bronco. I wanted to verify with him before ordering parts that my worn out shift fork could cause the grinding and...

Hey guys. I need to pull my chip out and put it in someone elses truck to help diagnose some performance problems that I believe are being caused by his tuning. My question is what will the chip do if I disconnect the selector switch from the chip? Will the chip stay in the position it was in...

I've been doing a bit of research on this turbo lately. I found some of the 6.0 guys here have tried it out and seem to like it and Jacob likes it on his D-max. Has anyone given this thing a try on a 7.3? Looking at the specs, it should flow more exhaust than the S366 most people run and with...

Hey guys. I need to wire up a PCS for a friend of mine's E99 SD cummins conversion. Most of it is pretty self explanatory, but there are a few things I haven't figured out yet. There are 6 unterminated wires coming off the range connector. -start1 and start 2 (one blue wire, one white wire) -2...

Truck and Antique tractor pull- June 22nd in Johnson City at the Blanco County Fairgrounds. This will be tractors 1965 and older and for the trucks we are having both a gas and diesel truck class. There will also be food and a kid's sled pull. We will be using the HWH sled. -Registration...

Hey guys. Does anyone have a wiring diagram for a PCS that shows the manual mode connection? I'm working on a way to convert a ratchet shifter to manually shift the trans through the PCS controller when in manual shift mode. If anyone has the diagram running around, I'd appreciate it.

Hey guys, listing this for my brother. He has an Industrial 62/80 Silver Bullet turbo he's trying to sell. It was only on his Dodge for maybe 1000-2000 miles. Turbo has no play and wasn't run hard. Specs: 62mm extended tip compressor wheel, 74mm turbine wheel, 14cm housing. Of course the...

Hey guys. I have a like new aluminum radiator for an SD 7.3 for sale. I had it in my truck for about a month. I only put around 1000 miles on it. I replaced it with a different one b/c I thought it was the cause of a cooling problem. It was NOT the cause of the problem and rather than change my...

Hey guys. Got a problem with my OBS. Fuel pressure seems to be continually rising.. I looked down at the gauge and it was reading 90psi. Drove it another 2 miles so I could park it and check it out. By that time it was at 95psi. I shut it down and pressure bled off, but as soon as I started it...

Any sponsors here carry a good quality aftermarket aluminum radiator for a 7.3L SD that will cool as good or better than the stock radiator? I need to change my radiator again and would like to get away from the plastic end tanks. Shoot me a PM with what you have. Thanks!

Got my 55w 6000k kit installed on my OBS this weekend and can't believe I didn't do it sooner. Happy enough with it that I will be getting a kit for my other truck before long. Install was pretty straight forward and the quality is top notch. The only thing I may change later on is I may...

Anyone know off hand what size the inlet and outlet is on the DI intercooler? I bought a used intercooler that was advertised as a DI intercooler about a month or two ago, but never looked at this until I just got it installed in my OBS. The inlet and outlet on the IC I have are both 3", so my...

Any sponsors here dealers for Caltracs??? Interested in getting some for my OBS soon. If so, PM me pricing. Thanks!

Not quite finished yet, but should finish up tonight. I know a bunch of y'all are probably electric fan haters, but please save all the bickering saying "this won't work for towing" and such. This has been a surprisingly easy mod to get done. I picked up the fans and radiator really cheap...