Need a 6.4 injector, another hard lesson learned.

[78f100]

I need one 6.4 injector, if anyone has any laying around and want to sell one or the whole set. Just for future reference make sure you take the ring off the injector before trying unscrew the two halves... Another lesson learned the hard way.

I bent one of the pins on the (idk what its called but its the round thing in the injector with 2 pins and 2 holes). Anyway I assume the ring on the nozzle bound up and the pin bent when I was pulling it apart.

 

[White_monster]

that sucks dude, check ebay, usually got brand new ones for cheap if no one has one they can spare.

 

[blk350on20s]

Ill see what i can get one at ford for. I get cost

 

[Dzchey21]

I didn't have any luck with the ebay ones. 3 injectors all thru balance codes. Put a ford reman in and it worked fine.
.check ebay for used take outs or the site
I think a guy is parting out a 6.4 on here as we speak

Sent from my DROID BIONIC using Tapatalk 2

 

[blk350on20s]

Ahh dustin your right. My buddy doug. Ill get ahold of him

 

[blk350on20s]

450 for the set. Motor had 107k on it

 

[Red_93_L]

I've got a set of 8 I'll sell for $350

 

[blk350on20s]

Boom there ya go. Thats a great price

 

[78f100]

I've got a set of 8 I'll sell for $350

I will take them, how soon can you ship them? and how many miles are on them?

 

[Dzchey21]

If you wanna sell any individual injector I might pick one up off ya for a spare

Sent from my DROID BIONIC using Tapatalk 2

 

[78f100]

If you wanna sell any individual injector I might pick one up off ya for a spare

Sent from my DROID BIONIC using Tapatalk 2

I will let you know when Iget them, I may sell you one heck I might give you one for all the free advice you have gave me...lol.

Have you ever seen one do that before? Or am I the only sucker that ever broke one. I saw a guy at a shop pull one apart and he didnt pull the ring off the nozzle and his was fine. I think mine was just really stuck and the nozzle twisted with the housing.

 

[White_monster]

There's been a few instances of damaged injectors during disassembly. Sucks this happened to you. I may be interested in a spare injector or 2 as well.

 

[78f100]

Is there a tq spec on these injectors when you put them back together?

 

[White_monster]

Ya. 50ftlbs.

 

[78f100]

There's been a few instances of damaged injectors during disassembly. Sucks this happened to you. I may be interested in a spare injector or 2 as well.

I will let you know when i get them.

Ant tricks to keep this from happening?

 

[White_monster]

When you disassemble them just crack the cup about 1/16-1/8 of a turn. Then tap the tip with a rubber mallet. Then turn a bit again. Tap again. Do this over and over till things are free. If it doesn't want to turn tighten it a bit then try again. Slow and steady wins the race on this one. Tapping the tip after each turn really helps. Also take a oring pick and scrap all the carbon from around the tip/cup area so nothing binds. Think that's it.

 

[Dzchey21]

I will let you know when Iget them, I may sell you one heck I might give you one for all the free advice you have gave me...lol.

Have you ever seen one do that before? Or am I the only sucker that ever broke one. I saw a guy at a shop pull one apart and he didnt pull the ring off the nozzle and his was fine. I think mine was just really stuck and the nozzle twisted with the housing.

Yeah mostly they actually stick in the nozzle. I have left the ring on the end a couple times and had no problems.

Haller told me lately he has been soaking in nozzle in penetrating oil before trying to tear them apart seams to help.

Sent from my DROID BIONIC using Tapatalk 2

 

[Dzchey21]

When you disassemble them just crack the cup about 1/16-1/8 of a turn. Then tap the tip with a rubber mallet. Then turn a bit again. Tap again. Do this over and over till things are free. If it doesn't want to turn tighten it a bit then try again. Slow and steady wins the race on this one. Tapping the tip after each turn really helps. Also take a oring pick and scrap all the carbon from around the tip/cup area so nothing binds. Think that's it.

That's good advice working the nozzle back and forth tighten and loosen is what seams to be the best. Rubber mallet helps too

Sent from my DROID BIONIC using Tapatalk 2

 

[78f100]

Thanks, bud I learn well the hard way...lol