Recent content by lc tpi
-
T500 vs stock pump test
ok so maybe i missunderstood some of the talk in the earlier posts. i thought it said some tuners set max icp to 2400psi.- lc tpi
- Post #85
- Forum: 7.3 Aftermarket
-
T500 vs stock pump test
i have a scan guage on my 95 7.3 . while out running some arrons i was watching the icp psi , i have 238/100's t500 and gearhead tunes with a 2000 sd computer, i watched my icp get to 3120 psi at full throttle but from 30 mph to 75 mph getting on the freeway. so its safe to say the tunes dont...- lc tpi
- Post #83
- Forum: 7.3 Aftermarket
-
-
thinking about going 1 piece driveshaft on rear
going to run a conversion u joint at the tcase with a superduty flange on my stock driveshaft.- lc tpi
- Post #11
- Forum: 94-97 Tech
-
thinking about going 1 piece driveshaft on rear
i will post one as soon as i can finish her. ive been swamped with work and kids. very little time to work on her only sundays.- lc tpi
- Post #10
- Forum: 94-97 Tech
-
thinking about going 1 piece driveshaft on rear
Involves rep inning the PCM plug and running extra wires to the trans and one extra sensor on the motor and few small other things like tuning on my chip for the ad programing- lc tpi
- Post #8
- Forum: 94-97 Tech
-
thinking about going 1 piece driveshaft on rear
I have read a few threads about doing it on the 5spd trucks but never found anyone that had done it on a e4od truck. I bought a electrical schematic for my 95 and have the schematic for a 2000. I put my Bts 4r100 in my 95 with a 2000 pcm .and as soon as I button everything up on the driveline...- lc tpi
- Post #7
- Forum: 94-97 Tech
-
thinking about going 1 piece driveshaft on rear
i will check with the local driveshaft shop i use and see if they can put a new weld yoke on the tcase side and run the 1410 at the top. and talk with them and see what they say about a one piece. they do have a top of the line driveshaft balancer for three piece drivelines and they do all the...- lc tpi
- Post #5
- Forum: 94-97 Tech
-
thinking about going 1 piece driveshaft on rear
i did find this. just a note my truck is lifted 4". http://www.emotoman.com/f250/driveline/f250shaft.htm- lc tpi
- Post #3
- Forum: 94-97 Tech
-
thinking about going 1 piece driveshaft on rear
hi guys , i have a 95 cc/lb 4x4 just swaped to a sd pcm 4r100 and sd tcase. instead of modifying my rear drive shaft to fit the sd tcase i was thinking of upgrading to the 1410 rear pinnion yoke and running a 1 piece driveshaft . i already have a sd front driveshaft but the rear i dont have. i...- lc tpi
- Thread
- Replies: 10
- Forum: 94-97 Tech
-
Gauge opnions
you must buy all your tools at harbor freight , it isnt worth my time replacing guages every few years . buy it once and do it right. yes even the good stuff fails but the track record for the good stuff is way better. when you want quality you pay more. you will have more money and time...- lc tpi
- Post #21
- Forum: 94-97 Aftermarket
-
Gauge opnions
ive had autometer in my 01 i now have isspro in my 95 love them, i bought a glowshift fuel pressure guage for the 01, 4 years ago and it lasted less than a year where you could only read half the guage. it was digital. wouldnt waste my dough on that crap ever again.- lc tpi
- Post #7
- Forum: 94-97 Aftermarket
-
New take on DIY 6637
you didnt have enough to do the exhaust? what about rad hoses?:thumbup: looks good.- lc tpi
- Post #22
- Forum: 94-97 Aftermarket
-
Smoked OBS cablights anyone....
yes that is the most important question.- lc tpi
- Post #13
- Forum: 94-97 Aftermarket
-
tube bender
i also have a jd bender . ive had it for 14 years. just like they have talked about clean tubing and lubricant will make them last. before they used aluminum pillow block they were steel and once you gall them they are a bi**h to fix. . i set mine up with hydraulic. bent many cages sliders...- lc tpi
- Post #19
- Forum: Welding & Fabrication Forum
