Search results

The Morimoto ones show that they replace 2015+ F150 and 2017+ Super Duty so I believe the housings are the same. Check under the 'compatibility' section: https://www.theretrofitsource.com/ford-super-duty-2017-morimoto-xb-led.html

You can see the wiring instructions here: https://pdf.ampire.de/directed/535T_englisch.pdf It's relatively straight forward. You wire it to constant +12v and ground. Then cut the wires between the switch and window motor and wire this in line with it. The rest of the wiring (for alarm triggers)...

The easiest way to get one-touch windows would be with this: https://www.amazon.com/dp/B00H4N1Y2O/ref=cm_sw_r_cp_ep_dp_32QjAbXPTHV1G I've used them in a few cars in the past and never had a problem. One module will add one touch up & down for 2 windows. You can also tie it in with an...

I don't have any firsthand experience, but when I was adding the OEM backup camera to my finacee's Malibu their kits kept popping up when I was doing research and the feedback all seemed positive.

Sent you a PM last week but haven't heard back. These still available?

Recon makes them. https://www.gorecon.com/categories/132/F-150-F-250-F-350-F-450-ILLUMINATED-EMBLEMS-Ford-F-Series-Trucks Check with the vendors on here, I'm sure someone carries Recon products.

Do you remember if the input shaft on the 2016 box was splined? Using pictures from RedHead's site for reference (can't find many detailed pics online), the 2008-2010 box should have the same shaft as the 2016 (non splined -...

I bought a steering box out of a 2011 6.7 to swap into my 08 Job 1 truck. I found out after I pulled my box that it's splined and the 2011 box isn't. The 2011 box just has a round shaft with two flat spots on it. I believe the intermediate shaft should be a direct swap so that the 2011 box will...

It only takes 5 seconds to right click a picture and reverse image search it. Try being honest in your for sale posts and you wouldn't have any trouble. :thumbsup:

Hmm.. Reverse image search shows that exact pic OP posted came from another forum from 2014, on an RV install.. http://www.irv2.com/forums/f104/exhaust-muffler-replacement-189733.html

Not exactly hidden, but I have flush mount LED cubes in my rear bumper I use for loading/unloading at night, extra reverse lights, etc. I've been looking at adding a strobe controller to them, in case I get caught on the side of the road/stop to help someone change a tire, etc...

Most of the Viper systems actually have a diesel wait to start input. You tie it into your wait to start light on the dash, and once the light goes out the truck will start. Compustar makes some nice systems too. Thinking about going with one of them next time just for their durable fobs. I...

PM sent.

KY. Zip is 40165

Price on center console?

Not sure about the climate control, but I have a buddy who had the same problem with his 6.7 and CTS2. Once you're in the truck and turn the key on, you should be able to tap the screen on the CTS2 to wake it up.

@autotruckservice I've been keeping up with it there. The attention to detail in these builds is mind blowing.

You can pick up the Sylvania resistors from the parts store for around $10, just wire one side to ground and the other to the turn signal wire. You can also have the dealer set the BCM up to eliminate the hyper flash. Great job on the build, they look awesome!

I ran across these on ebay: http://www.ebay.com/itm/H-S-Tire-Pressure-Monitoring-System-TPMS-08-10-Ford-Powerstroke-6-4L-Diesel-/171795191899?hash=item27ffca985b:m:mdXpfl4LhzCyQUoKNpBiMKw&vxp=mtr...

No problem! Yeah I remember the fuse was rated way higher than what we needed and the LEDs don't draw much at all. I have them on my 6.4 wired to the upfitters. I've run them hours at a time without having to worry about killing the batteries. After putting them in my truck my dad just had to...