Search results

Had a piece of farm equipment decide to come unhitched the other day and my bumper became a casualty. I'm wanting to build something steel and heavy duty but not sure what or how yet. I'm thinking a built in toolbox on each side, maybe D'rings or something. Wondering if anybody knows where...

I've been having an issue of complete lack of defrost in my truck, yet adequate heat through the dash vents. After searching it seemed the issue lied in the blend door actuator. So I purchased a new motorcraft one and did the swap, however no difference. I crawled under the dash with a light and...

Have had some issues with what seems to be fueling with my truck. Truck likes to throw a P0191 - Fuel Rail Pressure Sensor A Circuit Range/Performance code as soon as the key is turned to start and the odd time injector contribution codes for cylinder 2 and 7. I took the truck to a well trusted...

Looking at options to level my truck and I can't remember after how much lift radius drop brackets are needed. Was pretty sure 2.5" is max but can't find anything online. Thanks.

Was wondering if anybody had some experience with these tires? Tires are very affordable, Have good load and speed rating and seem to come well reviewed. Anybody have any experience with them on a 3/4 ton, seems everybody is running them on half tons, not much on 3/4 tons.

Looking for a part number for the female fitting going to frame rail fuel pump for my filter setup. Found this: https://www.aliexpress.com/item/9-49mm-ID8-180-degree-SAE-3-8-Fuel-pipe-fittings-Fuel-line-quick-connector-female/32813949447.html but not sure if it's the right connection. Thanks...

I'm looking at replacing my stock halogen headlights with leds using a conversion bulb with built in resistor etc. There seems to be piles of options however I'm wondering if there is any special wiring harness needed or something on top of the bulb or if everything is simply "plug and play".

I'm looking to get rid of the stock "bowl" fuel filter setup on the frame rail on my 2011. I would like to run a 10 micron into a 2 micron spin on filter setup. My issue though is as far as I can read it seems I would be pioneering this. My question is A) does anybody know of somebody who has...

So my dad is getting a bit of a mid life crisis and wants to go a bit higher with his stock 95. Truck is running 285/75r16s so looking for about 2.5 in the rear and about 4 in the front roughly. So far I'm thinking 3.5 inch reverse shackle, fox 2.0s on all four corners, and maybe either an inch...

Hey guys, as some of you know I took out the bottom end in my 6.7. Oil is full of shavings. Truck's on it's way to a diesel shop for a brand new bottom end and H and S ******s. Mechanic told me though to not be surprised if turbo was shot if that contaminated oil was pumped through it. I've been...

Hey guys, so my 6.7's been acting up on me and lately and I've been chasing problems. It went into limp mode a couple weeks ago forcing me too limp the last kilometer home, but then had no problems. However it's been more and more frequent that it goes into limp mode and I'm a bit at a loss...

Hey guys, I know there's a few of you guys from winnipeg hanging around so hopefully one of you guys can help. My 6.7 started acting up tonight as I was coming into the city. Idles like an inline engine and transmission doesn't want to shift past second, so I dropped into manual mode and limped...

Hey guys, so I come from a 7.3 background and am newer to the 6.7's. anyways, it's getting time for me to replace my air filter and was thinking going the 6637 route as everybody who mods their 7.3 goes that way. Was wondering if anybody has done it and has any notes or points worth sharing...

So I'm looking at adding more light to my old allis field tractor and have been researching light bar and pod options. I talked to a local guy and he quoted $85 a piece for 1400 lumen truck lite individual lights, up to $240 for 2500 lumen grote trilliant series lights. Was wondering just how...

I put my edge cts2 in my 6.7 about a month ago and last week it cut out. Had this happen in my 7.3 and it was the fuse for the cigar lighter cutting power to the obd2 port, thing is I can't seem to find the fuse directing power to the obd2 port, was wondering if anybody knew what fuse it should be?

First I'd just like to say that if this is in the wrong section I apologise. Second is my maybe crazy maybe not so idea. While lazily cruising a backroad the other day my mind started to wander more so to how badly I really wanted to be shifting gears manually, however just finishing a over year...

Hey guys, I'm on the hunt for a truck and can't seem to find anything clean and decent miled. As the title says I'm located in southern mb Canada (I'm sure there's got be some more of us around the forums) and i'm looking for a diesel. I'm looking for anything clean really, would prefer a 7.3...

So I discovered today that navistar had a version of the 7.3 for a marine application under the star powr brand named the m444e. These engines were supposedly rated at 300-310 hp. My question is a) hypothetically speaking, could you run m444e injectors in a 7.3 psd? And b) where could you find...