Search results

Okay guys I have a 6.0 in my shop that I need some advice on. Truck is a early 04 Background- truck had 205/100s and barder 71 now has stock both. The issue was the same in both scenarios. Issue- at idle the motor sounds like timing is off and it's loading up on fuel. Bring the rpms up and...

Installed a built trans from a trans shop i use regularly and have never had any issue. The issue that i am having is it will not make the 1-2 shift in Drive. All other shifts are fine but will not make the 1-2 you must rev out in 1st and lift and let it shift straight to 3rd. However if you use...

I have a customers truck kicking my ass i need of some advice Start with the history of the truck started out just studded and ****** it blew the gaskets went back with new studs and oringed the head. At this time i installed warren 205/100s barder, Barder stage 4, RCD thumper 1 hpop, regulated...

Currently I have a cooling mist setup with two 250psi pumps each feeding a CM12 nozzle, which according to the website flows ~14gph. That theoretically should give me a total flow of ~28gph at full flow. System is setup with a progressive controller with the first stage beginning flow at 12psi...

A set of used 7.3 head studs. Have been torqued one time. Like to get $450 for them

I have a gtx4294r that i purchased and have decided to go a different route. Comes with the exhaust housing and all. Going to see if there is any interest in it. Id like to get what i have in it as its brand new in the box only had it for a couple days. $2900 shipped I dont have any pics of it...

Parts obo plus ride Comp 910s, shim kit, and smith brothers prods(~10k miles on them) great shape just going to stiffer springs on built motor $300 used walbro fuel pump (kept up with 300/200s going to a fuel lab for 400s)- $40

Power stroke parts for sale all parts obo 7.3 Comp 910s, shim kit, and smith brothers prods(~10k miles) $300 Intake plenums- $40 Intake plenums w/ billet inserts- $50 obs hpop reservoir- $40 used forged rods- $300 2 superduty fuel bowls- $50 each front bumper(great shape, few scratches, no...

Long story short my old setup was too much for my forged rods and they let go, so I am building a motor and going to fill the block. Looking to fill it about 2in below the deck which should be right over the freeze plugs. I'm looking for some tips and tricks for filling the block? This will be...

Im selling my stealth srp1.1 has about 10k miles on it. It was just sent back to gary and checked out and gone through and updated larger rear bearing put in. Great pump supported my 300/200s flawlessly just went bigger. $700 shipped + a core pump

Iv got a 38r for sale about 10k miles on it. Has a diesel site billet wheel and adjustable wastegate actuator. Like to get 1000 shipped. Also will have a set of international bellowed up pipes for sale like to get 250 shipped Sent from my EVO using Tapatalk 2

Just wanted to share my results from the diesel nationals last sat at Rockingham. Fastest pass of the day was a 12.68 @ 103.?? Truck weighed in at 7800 ccsb. This was with my gearhead race tune. Truck runs awesome can't complain one bit loving the setup still have a few shifting bugs to work...

My buddys service truck is having some problems running while it is cold. When you first crank it up after it has been sitting for a period of time it will crank fine but as sion as you try to drive away and give it some throttle it dies hard and sometimes will cut off. If you let it sit an idle...

With my current setup i am having trouble getting my trans to shift properly. When 4wd launched it will tach the red line and bounce off the rev limiter for a sec then shift to second and lock the converter and move on. I did some datalogging with my AE and the pcm is not commanding the shift at...

Nearly new full force 250/100s only a few months old and about 7k miles on them. Oil changed at 4k and will be changed at 8k. Looking to get 1700 shipped

So there seems to be a growing trend for more and more people running larger injectors on pmr motors. I am in need of injectors mine are getting worn and i believe they have some damage from my hpop grenading. I have been doing some research and am going to go with casserly 250cc hybrids but am...

My srp1 pump tore up last week. The entire pump grenaded and cracked the housing in the process. The pump is taken care of, Gary is warrantying the pump and i am going to upgrade to the srp1.1. I currently have a stock 17 degree pump on the truck and the truck is running until i get my stealth...

My truck has recently began not starting on occasion. It doesn't do it all the time but it seems like it is becoming more and more frequent. Sometimes it will just turn over and other times it will fire right up like its brand new. When i try to start the truck all it does is turn over, it...

So I heard a little bit about these Farmers injectors that are supposed to flow 650+ cc of fuel. I tried doing a little research on them and they the general consensus is the guy is a joke, but then others are all for the guy and think he is the best thing since sliced bread. Is there any...