Search results

Hey guys could use some help...its not a powerstroke but an 08 v10 f450 xl 6spd man.i updated the pcm with an ids, everything went fine.. But no crank.. Jump it out under the hood and starts up fine. Datalog shows that the starter relay is disabled... Its an xl truck so it doesn't have a chip...

Looking for a decent set of used injectors for a late 6.0. Let me know what you have. Thanks psn

Uograding to the full leafs so putting these up for sale. They are still in the truck and will be removed in the next week after the springs show up. Currently they are installed in a 2008. Im am including the 2" 2011 lift blocks, and ubolts for a 05-10 truck. These will include the 2011...

For sale is a factory subwoofer box loaded with a jl audio 8w3v3-4 subwoofer, fleece performance subwoofer spacer and a nvx mpa-1 amp. This is the cleanest most factory looking setup out there. Sounds like a much bigger sub then what's there. Sub and amp are less then a year old. Nvx amp is...

Unlocked mini maxx in box. $1100 shipped to the lower 48

Have a locked ******* Dashdaq xl I was using for monitoring. Unit is vin locked. ******* charges $500 to unlock. Comes with dash mount. $350 shipped

Hey psa. What do you think this noise could be? Sounds valvetrainish to me but not sure. Only seems to be hot and at higher idle. Backround on it is has ford enhanced (4000 miles on it)shortblock, elite pushrods, springs,valves(carry over approx 20k on those), and rockers were installed at...

Looking for the transmission harness for a 02 with esof. Plugs into the trans, transfercase and runs up to the plugs on the drivers fender liner. Part number is 2c3z-15525-ga. It's obsolete from ford now :/. Thanks

Hey guys. Trying to track down this vibration. Would a pinion flange from a 05 fit the 08 rear end? I know there is something with the pinion changed with the 08s and newer. Thanks psa

5r110 pulled from my 6.4 job 2 truck. Had 100k on it, shifted great. Has a precision of New Hampshire billet triple disc converter in it. Converter has about 2500 miles on it. Only replaced to go with a twisted stage 3. Asking $400 for trans and $500 for the converter. Or buy both for $800...

Who Makes a decent input shaft. The billet one broke and still a piece stuck in the converter (any tips on getting it out) :\ Rant warning: I Broke the one in a stage 3 from twised diesel. Was pulling about 4500lbs, just pulled off the interestate, heading down a secondary road, made...

Pulled this all off my 6.4..purchased lpfp and filter housing from ford last year, about 5k miles on those. Also includes the lines from pump to block and the head lines that run up the side of the block to the filter. Upper fuel filter housing, and line from filter to hpfp. $250 shipped...

What can I do to do away with the water in fuel message on the dash? I keep getting It thrown even tho it's all been removed lol. I had this problem before with the truck, but had a factory fuel system in place and thought it was just a dirty tank causing it. Currently has airdog 2 pump with...

6.4 bare block for sale. Standard bore, would only take a rehone and cam bearings to go again. Had a crank break (search for my post). Had between 30-40k miles on it, was a new ford block when engine was built. Small nick out of the bottom of cylinder of #7 in the bevel part. Still removing...

Stage 1.5 turbo. Few months old. Build date of 6/3/14. Was originally a stage 1,had a rear seal leak within the first 50 miles, was sent back and changed to a 1.5. 2k miles on it since then. Returned truck to stock and trading it in. $1000 shipped, no core wanted/needed

Xrt pro unlock ready to delete again. $1100 shipped

Set of 8 standard bored pistons pulled from a ford reman enhanced shortblock before it was installed or ran. Pistons, rings, pins, locks. $600 shipped.

Brand new sealed Suncoast billet flex plate. Ordered in for a customer that never picked it up, has June 2014 sfi date. $600 shipped

First one of these posts I've done, so ill start with a little history...purchased the truck with a engine that was down on compresion in one cylinder, and 3 others that were so so.. Tore it apart and found #2 was .035 over sized already lol So I found a engine with roughly 30 k in it that...

Up for sale is a 6.4 block, it needs cleaning on the gasket surfaces(mostly just the bedplate). as they rusted from sitting. Will need to be bored .020-.030, was never studded, been sitting around for quite some time. $400 obo buyer pay and arrange freight Brand new exhaust back...