Search results

7.3l powerstroke parts I have an EBV deleted pedestal for early 99's only, professionally welded - $50 one used valve cover harness (UVCH) - best offer a brand new HPOP injection pressure regulator (IPR) from Autozone - $75 A known good used IPR - best offer plus shipping nearly brand new...

Runs good, almost no shaft play, factory wicked wheel. Located in Brunswick OH, you pay shipping.

Superchips 1950 tuner, has an economy and 120hp mode for 7.3's. I drove around in economy mode and it helped mpg's a lot. I also liked the shifting a whole lot more than the factory tune. works most Fords since 1999. unlocked and ready to ship - $250 Autometer gauge set (boost, trans temp...

I'm just full of questions today. I've never seen a factory intake for an early 99, but mine looks like an OE but it's in better condition than the rest of the engine bay. Any thoughts?

I'm looking at this broke switch and wondering if I need just the button switch or the whole shifter. Anyone seen one broke like this before?

Would this oil be considered aerated?

I posted up a thread back in December about how my truck was running rough. I ran through every rough running flowsheet I could find. After doing all kinds of tests, I ended up extending my fuel pressure tester 12" so I could drive and see it. Turned out my o-ring in the FP regulator was...

I was doing a little searching and was surprised that it's not common to do a Bronco style removable top. I found one pretty cool picture, but that was about it. I was looking at my Ex today and it looks like a real big challenge, but there are 8 door Excursions out there. I think it would...

Appx 145K miles, good even compression. Long block only with oil pan, cooler, and front cover on. fits 99-03. Ready for delivery. $1400 shipped to a place that can unload a pallet. or pick up in 44212 Ohio.

Works perfect, some of the illumination bulbs are missing though. It's one of the last pieces I have from a truck I parted out. 208k miles on the odo. from a manual truck so no trans temp gauge. $70 shipped from ohio

I have a trans from a 2000 6.8l that had a rather firm 1-2 shift, maybe too hard. It had a tune on it so I wasn't sure if the 1-2 shift was programming or a sign that the transmission is bad. I want to sell it but I don't want to list it as a good transmission if this is a broke one. Any...

What's the simple, cheap way to filter WMO to mix in with diesel for my powerstroke? Im thinking to let the WMO settle for a few weeks to get water out, then strain through socks down to a micron. If mixing 2-4 gallons into a 40 gallon tank would that be sufficient? Am I missing anything...

On the early 90's u-hauls I used to work on they had a big mechanical fuel pump in the middle of the valley (used to call it a spider pump). Why aren't these as good as the cummins motors from the same era (talking reliability and power potential wise here)? I'm not real familiar with either...

This is a question for you guys that remember using the snap on brick scanner (mt2500 model). I have the 01 Ford cartridge and I don't think I can do a perdel PID. Is this a limitation of the scanner or the cartridge? I think I remember there being a diesel cartridge that I don't have, and I...

I finally scored a set of bushwacker fender flares off craigslist - $200. I'm thinking to paint them body color, but I'm not sold. What do you guys think? My truck: Heres these flares on a truck:

Have a look, any questions just ask. http://cleveland.craigslist.org/cto/3668580468.html Thanks

I have two HPOP's and I was wondering if anyone offered a service to see which one is healthier? I have my 200k mile 15 degree and a unknown high mileage 17 degree.

Could I add something like this in between my tank and pump? http://www.amazon.com/Wix-24309-Filter-Mounting-Base/dp/B000CSIO0I Then just pull out the fuel filter in the engine? Would the pump mind pulling through it? And then would it be more effective at removing water/contaminants? I was...

Shot in the dark, but if anyone has good lower mileage AD injectors that are gonna be sent in as cores I would make it worth your time to send them to me and I'll send you my set of AD/AE's. Might help ease the pain of the new injectors you are buying :) I don't know if mine are good, they...

Does anyone know a link to info on rebuilding or at least checking used injectors? I understand people used to do it but there's no info out there on what they were doing (that I can find anyways). I have a set of AD/AE's that come from who knows where and I'd like to take them apart, clean...