Search results

I've got a 2001 dually that has a bad front wheel bearing. I decided to do both of them since they are original. I purchased the hub assembly/wheel bearing from Rock auto for a good price. I called the dealer to see if there were any other seals/ parts to change and they mentioned a few that I...

I have a spare International 444e that I'm converting over to a powerstroke and looking for parts to convert it. I already converted one 444e to a 2001 superduty with the parts off the old engine. Now I'm looking to buy parts for the other 444e and am wondering what years are the same. The...

I've got an extra International 444e that I need these parts to convert it to a powerstroke superduty. It's a spare engine so I'm not in a hurry for the parts. I'm located in Chardon Ohio 44024 so they would have to be shipped or close enough where I can pick up. Please pm or email me at...

I purchased a good running 444e out of a school bus to replace my worn out 7.3. Took my old engine and the replacement over to a local shop, Rosewood diesel to swap the parts over from my old engine to the new engine. I used the hpop from the International as it was running well. The...

Selling a hpop out of a running truck with 170k on it. The pump shows a tag that says remanufactured so it's not the original pump. Selling as is but the truck ran fine with no issues. $250 obo

Have a 7.3 out of a 2001 f550 with 170k on it that was removed because of low compression, lots of blow by. Actually runs pretty good though. Going to be just the bare long blocks as the injectors and hpop will be used. Located east of Cleveland Ohio. PM me if you're interested.

I have a good set of used pipes/collector off of a southern truck with minimal rust. PM me if interested.

Doing an engine install and I noticed the vanes on the intake side are a little dusted. They're still all there but definitely seen some dust through them. the turbo looks like it's newer and there's very little end play in the shaft. Can I just replace the wheel with an aftermarket wheel or...

Trying to find out more info about it and there doesn't seem to be a lot of informational forums on the topic. Anyone know the best place to get information?

I have some turbochargers off a 2001 444e International engines which look to be the same as the stock turbo on a powerstroke minus the waste gate. Have a friend that just installed one on his SD and it seems to run the same as his regular stock turbo. They have minimal end play and the fins are...

Have a set of good condition AD injectors that have been remanufactured. Not sure how long ago but the truck runs well with plenty of power and has no codes. The truck has 170k on it and they are remaned so I'm sure they don't have many miles on them. We only needed the long block out of it...

I have a hpop reservoir off of an international 444e that has a good power steering pump attached. These can be modified to bolt up a second hpop over the stock one for a dual hpop setup. Selling the reservoir and the power steering pump with the gear you'll need to mount to a hpop. Pm me any...

Have a good used turbo pedestal for a 7.3 powerstroke. This is off of a good running truck we parted out for the long block. It is newer and has been recently replaced. PM me offers.

Taking the engine out of my 01 SD and replacing it with a 444e from a school bus. Engine has 170 k and runs good but has signs of iron in the oil from an oil analysis. Also found very fine iron dust on the oil drain plug and in oil filter. Engine does have blow by but does run good. Instead...

Well, I'm looking to purchase a engine out of International school busses that are actually 444e engines . Basically the same as a 7.3 powerstroke with some different bolts ons. I looked at 4 of them today and the miles ranged from 130,000 to 160,000. Years ranged from 1999 to 2001 and they were...

I'm going to be purchasing a used International 444e which are either out of school busses or an International utility bed truck. The guy has 7 of them from years 99 to 2002 and I get to pick the one I want to replace a worn engine out of my 2001 SD. They are all running and most are...

I'm installing a good running low mileage 444e International and am wondering what gaskets and seals I should change out while I'm doing the swap. Gaskets aren't very expensive and I figure I may as well do them while it's easy. So far I'm doing the oil pan sea, oil cooler, exhaust manifolds...

I'm not selling these but I'm buying one to put in a truck and I think they'd be good engines for anyone that needs a long block or core possibly. I'm in Ohio and know of a guy that has purchased several 1999 to 2001 International school busses that are in the 120,000 mile range. They have...

I may need an engine for my truck which is a 2001 model and I found a good running 7.3 out of a medium duty International truck? Are the blocks, injectors hpop the same? I know the computers are different but not sure what's the same on it and what I could use off of it. It's still in the...

I have a 2001 Ford F550 Automatic 7.3 diesel that I purchased a year ago and up fitted with a contractor body I built. I'm in Ohio and wend down to Alabama to purchase this truck as I wanted something clean and wanted one of the older diesels as I have another 7.3 in my fleet that has been...