Recent content by space_heretic

Hi I'm down in ft hood tx I've had some issues with my truck. I've went through it and 2 different shops no body can pinpoint the issue. I saw a ad on c list for a shop in cedar hill called diesel speed and marine.they rebuild injectors and hpops just looking for reviews before I take my truck...

Anyone? Sent from my iPhone using Tapatalk

right now on a 80hp dp tuner flash tune. Trying to fix a multitude of other issues this truck was severely neglected prior to me purchasing it. The engine and turbo are about 5 months old though. Any ideas on the sound? ive listened and its worse when warm when cold i can gun it and not...

I have two strange sounds coming from my turbo. They are fairly recent boost seems fine. noticed some white smoke lugging the engine but clears up when warm. Injectors are 160/100's, 4 inch exhaust,4 inch intake, riff raff frx. Also noticed some idle vibration.

Looking for motorcraft 7.3 zd11 glow plugs, icp and pigtail, valve cover gaskets with harness. Just got this engine rebuilt upgraded injectors and turbo and these parts decide to fail. Looking to save a few bucks if you bought some parts and decided not to use. Thanks Sent from my iPhone using...

If your beds not got any broken through spots just sand blast it and throw some por15 on it. Than slap that bed liner back on it. They make none rivet style for the same price sand off the loose rust on those bed sides and spray rust converter. If the inspection places give you issues make up a...

Although I don't have rust that bad I still have a blown cab corner and a lot of other rusty spots. I bought fender flares from prestige they are rivet style. Good customer service even sent me a new rear set free after a flare flew off on freeway. I plastidiped the lower half of the truck to...

No you didn't miss the result's my mustang got a massive oil leak and i just fixed it. I did however find out that the injectors are 160/100's. Once work slows down a bit ill hit the dyno and post results.

Im going to have my 99 f250 run on the dyno for a pull right after my mustang.Just to see what it makes so its pretty conservative compared to some of you guys. engine 60k .20 over 38r stage 2 single shots DP 80hp econo tune(temporary until i get a 6 pos) frx 4 inch afe turbo back no muffler...

Thanks anything else I'm forgetting that I should be worried about? Does this seem like a bad deal?i was quoted 5k for a rebuilt long block. He's asking 4k for this one.(installed)

Well my mechanic is offering me what seems to be a good deal. I had originally taken my truck in to get the engine rebuilt. Well mid rebuild he offers his 60k engine(rebuilt .20 over) 38r and stage 2 single shot injectors with tune for 1000 less than a full rebuild. My engine is completely...

This is what the kit came with I already bought and installed new o rings for injectors Sent from my iPhone using Tapatalk - now Free

Yup got a 99.5 but don't have a AE injector every single one is AD I did order a frx so I should be good to go. Also I noticed the felpro kit came with a **** ton of o rings. Anyone got a break down on these? Sent from my iPhone using Tapatalk - now Free

I'm rebuilding the top end of my truck. I have all the rocker arms in order but does it even matter? Injectors and pushrods I kinda messed up on I had them in order but my son rearranged positions. So will there be any issues. Lastly reading a rebuild guide it says pushrods go copper end up. But...

If I remember right it's two ounces of pag per hard part removed. Don't forget some ac solvent to clean out the lines. Get the pag and solvent from napa. It's a rather simple process. Make sure all the I rings are serviceable and to replace orifice tube and receiver/dryer. Sent from my iPhone...